manualshive.com logo in svg

FARMSCAN Jackal v2, General Description Manual

Share
Download
FARMSCAN Jackal v2 General Description Manual Download Page 25

 

September 2015 

www.farmscanag.com 

AM-JACKAL-3 

24 

Flow Meter Setup (Wizard) 

FLOW METER SETUP (WIZARD) 

 
The Jackal can be configured to monitor liquid products. If only one input is used the 
main screen will display the flow information is L/min or gal/min, or, if using the 
speed & area function the Jackal can also display L/Ha or gal/Acre.  

 

At no stage can the Jackal take into account multiple spray sections turning on and off 
and adjusting the Ha/Ac to suit. 

Refer to 

PAGE 31

 for Rate Monitor setup to display L/Ha 

Sensors Required 

x

 

Flow Sensor (2 or 3 wire) 

Available Connections (

PAGE 4

) 

This setup section assumes that physical wiring for the required sensors 
have been completed.   
If not please refer to 

PAGE 7

 on wiring requirements.  

NB. 3 wire flow sensors need to be in 

B2-B6. 

If a 2 wire flow sensor is being used, please use 

B1.

 

SETUP 

 
This is example is using a 2 wire (Sine Wave/Coil) flow sensor into B1 

 

 

 

From the front screen press 

SETUP

 

Highlight 

WIZARD

 & press 

SELECT

 

Highlight 

FLOWMETER

 & press 

NEXT

 

 

 

 

Highlight the 

INPUT

 number X: the 

sensor wire is connected into on the 

rear of the Jackal & press 

NEXT

 

Enable the input by pressing 

EDIT

 

Choose your unit of pulse. 

pulse/L or pulse/gal 

 

 

Choose your calibration method : 

Auto Set (

Next Page

)

  

or 

Manual Ratio (

PAGE 26

)

 

 

 

 

Summary of Contents for Jackal v2

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands