Farmet DUO Operating Manual Download | Manualshive

Page: 37 / 48

background image

OPERATING MANUAL

OILSEED SCREW PRESS FARMET DUO

Page

37

of

48

10.

DISPOSAL OF THE MACHINE, PROTECTION OF THE

ENVIRONMENT



The Owner must ensure that the Equipment is disconnected from the power supply
prior to the commencement of disposal.



The Owner must ensure that steel parts and parts contaminated with the transmission
oil and lubrication grease are separated during the disposal of the Equipment.



The Owner must cut the steel parts according to the safety regulations and deliver them
to the usable by-products collecting station. The Owner must follow valid regulations
on wastes when disposing other parts.

«
...
35
36
37
38
39
...
»

Summary of Contents for DUO

















































Reviews:

No comments

Related manuals for DUO

Brand: 80% Arms Pages: 12

Brand: Stanford Research Systems Pages: 42

Brand: Marson Pages: 6

Brand: DRO PROS Pages: 2

Brand: Mean Well Pages: 35

Brand: Glendo Pages: 2

WOOD MILL G9959

Brand: Grizzly Pages: 52

Brand: HORN'UP Pages: 20

Brand: MSA Pages: 17

Brand: TDK-Lambda Pages: 20

Brand: TAPCO TOOLS Pages: 4

Brand: Gedore Pages: 246

Brand: Uniflex Pages: 44

ARO 7672-A18-EU

Brand: Ingersoll-Rand Pages: 28

Brand: Matrix Pages: 46

Brand: Terratek Pages: 15

Brand: Alpha Pages: 28

Brand: One Stop Gardens Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands