manualshive.com logo in svg

FarmBoy FB-BC-8642, Operation Manual

Share
Download
FarmBoy FB-BC-8642 Operation Manual Download Page 4

FarmBoy

™

 

BRUSHCUTTER 

FB - BC- 8642 / 8652

 

 

: www.kisankraft.com 

: [email protected] 

: +91.80.22178200 

 

Page 4 of 28 

 

Wear protective 

gloves.  

 

The port to refuel the "MIX 

FUEL"

 

 

 

Wear safety 

footwear

 

 

 

The guaranteed noise level  

 

Danger: Toughing 

the rotating blade is 

forbidden.  

 

With this symbol the 

manufacturer confirms that 

this tool is in accordance 

with applicable European 

directives.  

 

Beware of thrown 

objects.  

 

 

Hot surface: Risk of burn. 

 

Keep away from 

fire  

 

 

Keep all children, 

bystanders and helpers 15 

meters away  

from the brush cutter  

 

 

IMPORTANT

   

If warning label peel off or become soiled and impossible to read, you should contact the 

dealer from whom you purchased the product to order new labels and affix them in the 

required location(s).   

 WARNING

 

 

 

Never modify your brush cutter. We won't warrant the machine, if you use the remodeled 

brush cutter or you don't observe the proper usage written in the manual.  
 

 

Summary of Contents for FB-BC-8642





























Reviews:

No comments

Brands by name

Popular brands

Load more brands