manualshive.com logo in svg

FarmBoy FB-BC-8642, Operation Manual

Share
Download
FarmBoy FB-BC-8642 Operation Manual Download Page 11

FarmBoy

™

 

BRUSHCUTTER 

FB - BC- 8642 / 8652

 

 

: www.kisankraft.com 

: [email protected] 

: +91.80.22178200 

 

Page 11 of 28 

Assembly 

Installing Handle  

 

1.  Loosen the 4bolts on the upper cap and insert 

the handles equally. Retighten the bolts. 

2.  Put the handle assembly into the bracket and 

put the upper cap over it. Tighten the cap 

securely. 

Connecting Throttle Wire  

 

1.  Remove the air cleaner cover. 

2.  Connect the end of the throttle wire to the 

joint on the top of the carburetor.

 

Connecting Switch Wires 

 

Connect the switch wires between the engine and 

the main unit. 

Pair the wires of the same color.

 

Installing Protection Shield  

 

Attach the protection shield with the bolts combined 

to the shaft tube. 

Installing Cutting Blade  

 

1.  Put the angled bar (1) into the side holes 

of the gear case (2) and the plate (3) so 

as to fasten the axle. 

2.  Mount the blade (4) and the washer (5) 

onto the axle. 

3.  Mount the washer (6) and the nut (7). 

Fasten tightly anti-clockwise. 

Summary of Contents for FB-BC-8642





























Reviews:

No comments

Brands by name

Popular brands

Load more brands