Farm King Model 1050 Operator And Parts Manual Download Page 78

Page: 78 / 174

Operation - 10" Backsaver Auger

Winch Operation

Figure 129

Move the lever (Item 2)

[Figure 129]

to the left

(towards the hitch) to raise the boom cable (wind

cable). Move the lever to the right (away from the

hitch) to lower the boom cable (unwind cable).

NOTE: Never have less than three wraps of cable on

the drum of the winch.

Hopper Mover Operation

Move the lever (Item 1)

[Figure 129]

to the right

(away from the hitch) to move the hopper to the right.

Move the lever to the left (towards the hitch) to move

the hopper to the left.

Adjusting Flow Control Valve

Figure 130

Turn the knob (Item 1)

[Figure 130]

on the flow

control valve “IN” to decrease the speed the auger

lowers. Turn the knob “OUT” to increase the speed

the auger lowers.

Loosen the nut (Item 2)

[Figure 130]

and turn the

knob all the way in (tight). The approximate initial

setting should be 3-1/2 turns out from the tight

position. When set, re-tighten nut to set position.

NOTE: Be sure that the valve is slightly open before

raising the first time or auger will not lower.

B-0756

B-0695

Summary of Contents for Model 1050















































































































































































Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands

Farm King Model 1050, Operator And Parts Manual

Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands