Farm King Model 1050 Operator And Parts Manual Download Page 60

Page: 60 / 174

Assembly - 10" Backsaver Auger

HYDRAULIC ASSEMBLY

Hydraulic Cylinder Hose Installation

Backsaver Auger 1050 Flow Control Assembly

Figure 105

Locate one each of the following components:
1. 08 MORB x 08 SWFNPT 45° Elbow

2. 08 MNPT x 08 MNPT Straight Adaptor

3. 08 FNPT One Way Flow Control Valve

4. 08 x 010 MJIC x 08 MNPT Hydraulic Hose

NOTE: Apply teflon tape to the male threads of each

fitting.

Install the 08 MNPT x 08 MNPT straight adaptor into

the flow control valve

[Figure 105]

Install the 08 MORB x 08 SWFNPT 45° elbow onto

the 08 MNPT x 08 MNPT straight adaptor

[Figure

105]

Install the 08 x 010 MJIC x 08 MNPT hydraulic hose

into the 08 MORB x 08 SWFNPT 45° elbow

[Figure

105]

Backsaver Auger 1060 Flow Control Assembly

Figure 106

Locate one each of the following components:
1. 08 MNPT x 08 MNPT 90° Elbow

2. 08 FNPT One Way Flow Control Valve

3. 08 x 010 MJIC x 08 MNPT Hydraulic Hose

NOTE: Apply teflon tape to the male threads of each

fitting.

Install the 08 MNPT x 08 MNPT 90° elbow into the

flow control valve

[Figure 106]

Install the 08 x 010 MJIC x 08 MNPT hydraulic hose

into the 08 FNPT One Way Flow Control Valve

[Figure

106]

When installing and servicing hydraulic systems,

clean the work area before assembly or disassembly

and keep all parts clean. Always use caps and plugs

on hoses, hydraulic tubes and ports to keep dirt out.

Dirt can quickly damage the system.

Contain and dispose of any oil leakage in an

environmentally safe manner. Some regulations

require that certain spills and leaks on the ground

must be cleaned in a specific manner. See local, state

and federal regulations for the correct disposal.

B-0694A

B-0694B

Summary of Contents for Model 1050















































































































































































Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands

Farm King Model 1050, Operator And Parts Manual

Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands