Farm King 4480XD Quick Start Manual Download Page 11

Quick Guide - 4480XD Bale Carrier

11

Buhler Trading Inc. 1260 Clarence Ave. Winnipeg, MB. R3T 1T2
Tel.: (204) 661 - 8711 | Fax: (888) 524 - 1003 | www.farm-king.com

Warranty Registration Form

This form must be filled out by the dealer and signed by both the dealer and the customer at the time of delivery. 
Forms may be faxed to 204-654-2503 ATTN: Farm King Service/Warranty Administrator.  
Forms may be emailed to [email protected] or submitted online at farmkingdealers.com.

Equipment Model:

Serial Number:

Delivery Date:

I have thoroughly instructed the buyer on the above described equipment which included the Operator and Parts Manual 
content, equipment care, adjustments, safe operation and applicable warranty policy.

Date:

Dealer Rep. Signature:

The above equipment and Operator And Parts Manual have been received by me and I have been thoroughly instructed as to 
care, adjustments, safe operation and applicable warranty policy.

Date:

Customer / Owner Signature:

Remove this Warranty Registration Form from the Operator And Parts Manual. Make two copies of the form. Send original 
Warranty Registration Form to Farm King. Give one copy to the customer and the dealer will keep one copy.

Customer Name:

Customer Address:

City:

Prov / State:

Postal / Zip Code:

Phone:

Dealer Name:

Dealer Address:

City:

Prov / State:

Postal / Zip Code:

Phone:

Dealer Inspection Report:

Bearing Seals
Lubricate Machine
Wheel  Nut Torque
Fasteners Tight
Pusher Sprocket And Chain Tension
Hydraulic Hoses
Electrical Harnesses
Tire Pressure

Safety:

All Lights And Reflectors Installed
All Lights And Reflectors Cleaned And Working
Safety Chain On Hitch
All Decals Installed
Guards And Shields Installed And Secure
Review Operating And Safety Instructions
General Adjustment And Set-up Procedures
Transportation Requirements And Regulations

Summary of Contents for 4480XD












Reviews: