Farm King 1266 Operator And Parts Manual Download Page 28

28

Farm King Limited Warranty

This document limits your warranty rights.

Base Limited Warranty
Buhler Industries Inc. provides this warranty only to original retail purchasers of its product. 
Buhler Industries Inc. warrants to such purchasers that all Buhler Industries Inc. manufactured 
parts and components used and serviced as provided for in the Operator’s Manual shall be free 
from defects in materials and workmanship for a period following delivery to the original retail 
purchaser of 12 months (80 days for commercial applications). This limited warranty applies only 
to those parts and components manufactured by Buhler Industries Inc. Parts and components 
manufactured by others are subject to their manufacturer’s warranties, if any.

Buhler Industries Inc. will fulfill this limited warranty by, at its option, repairing or replacing 
any covered part that is defective or is the result of improper workmanship, provided that the 
part is returned to Buhler Industries Inc. within thirty (30) days of the date that such defect or 
improper workmanship is, or should have been, discovered. Buhler Industries Inc. reserves the 
right to either inspect the product at the buyer’s location or have it returned to the factory for 
inspection. Parts must be returned through the selling representative and the buyer must prepay 
transportation charges. 

Buhler Industries Inc. will not be responsible for repairs or replacements that are necessitated, 
in whole or part, by the use of parts not manufactured by or obtained from Buhler Industries Inc. 
Under no circumstances are component parts warranted against normal wear and tear. There 
is no warranty on product pump seals, product pump bearings, rubber product hoses, pressure 
gauges, or other components that require replacement as part of normal maintenance. Also: 
Buckets and Bucket Tines carry no warranty, Bent Spears carry no warranty, Snowblower Fan 
Shafts carry no warranty, Mower Blades carry no warranty, Portable Auger Parts Have Two (2) 
Year Warranty, Loader Parts Have Two (2) Year Warranty. The purchaser is solely responsible for 
determining suitability of goods sold. This warranty is expressly in lieu of all other warranties 
expressed or implied. Buhler Industries Inc. will in no event be liable for any incidental or 
consequential damages whatsoever. Nor for any sum in excess of the price received for the 
goods for which liability is claimed.

Repair Parts Limited Warranty
Buhler Industries Inc. warrants Farm King replacement parts purchased after the expiration of the 
Buhler Industries Inc. Limited Warranty, and used and serviced as provided for in the Operator’s 
Manual, to be free from defects in materials or workmanship for a period of thirty (30) days 
from the invoice date for the parts. Buhler Industries Inc. will fulfill this limited warranty by, at 
its option, repairing or replacing any covered part that is defective or is the result of improper 
workmanship, provided that the part is returned to Buhler Industries Inc. within thirty (30) days 
of the date that such defect or improper workmanship is, or should have been, discovered. Such 
parts must be shipped to Buhler Industries Inc. at the purchaser’s expense.

What is Not Covered
Under no circumstances does this limited warranty cover any components or parts that have 
been subject to the following: negligence; alteration or modification not approved by Buhler 
Industries Inc.; misuse; improper storage; lack of reasonable and proper maintenance, service, 
or repair; normal wear; damage from failure to follow operating instructions; accident; and/
or repairs that have been made with parts other than those manufactured, supplied, and or 
authorized by Buhler Industries Inc.

Warranty - 1266, 1272, 1276 & 1282 Conventional Auger

Summary of Contents for 1266

































Reviews: