Fargo DTC1000Me Service Manual Download

Page: 74 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 74

Remove/Replace the Flipper Cover

Step Procedure

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Caution: Please be careful not to force any of the snapping parts as they could break with

too much pressure. When replacing the Covers or any parts, do NOT pinch any wires.

Remove the Top Cover of the printer.

Remove the Dual-Sided Printing Module from the printer.

Short Dual-Sided Printing
Module shown

D930010-06

Tools needed:

T10 Torx screwdriver

Estimated Repair Time: 15 min

Preparation:

Remove the top cover of the Printer and Dual-Sided Printing

Module from the Printer

Important:

This procedure can only be performed by authorized service

personnel.

Short & Tall use common parts

Top cover D930192-01 DTC4250e/4500e

Top Cover D930192-03 DTC1250e

Card Bin D930193-01 DTC4250e/4500e

Card Bin D930193-03 DTC1250e

Flipper Door D930194-01

The Tall Dual-Sided Printing Module uses the Lamination Cover

Summary of Contents for DTC1000Me


















































































































































Search results

Summary of Contents for DTC1000Me

Reviews:

Related manuals for DTC1000Me

Brands by name

Popular brands

Fargo DTC1000Me, Service Manual

Search results

Summary of Contents for DTC1000Me

Reviews:

Related manuals for DTC1000Me

Brands by name

Popular brands