manualshive.com logo in svg

FARGO electronics Quatro Quatro ID Card Printer, User Manual

Share
Download
FARGO electronics Quatro Quatro ID Card Printer User Manual Download Page 40

36 Troubleshooting

encoded properly or encoded onto a bad magnetic stripe,
the printer is unable to verify the encoded data. When this
happens, the printer will simply eject the card before
printing begins and the on-line LED will begin flashing.
Press the on-line button to resume encoding and printing
with a new card.

The on/cancel LED light is flashing.

¥

If the on/cancel LED is flashing, this indicates a possible
error with your printerÕs memory. Contact your authorized
reseller for technical assistance.

I’m having problems printing from Windows 95/98.

¥

Print with either the 

32-Bit Print Spooler

or the 

Write

Direct to Port

option selected from within the printer

driver setup (see Chapter 4, Section IV for more
information on these options). In most cases, one or the
other of these options will provide the best results when
printing from Windows 95/98.

¥

Due to the wide variety of PC hardware and software
configurations, however, some systems may print more
effectively through the Windows 95/98 print spooler. If
you choose not to print with either the 32-Bit Print Spooler
or the Write Direct to Port option selected, but instead wish
to print through the Windows print spooler, the following
steps will help you optimize your system for printing:
1.

Click the 

Star

t button, point to 

Settings

, and select

Printers

. When the Printers window appears, click on

the Quatro printer icon using the 

right

mouse button,

and select the 

Properties

option.

2.

Select the 

Details

tab, then select the 

Spool Settings

button.

3.

Select the 

Print directly to the printer

option and click

on 

OK

. 

4.

Again from the Details tab, select the 

Port Settings

button.

5.

Deselect both the 

Check Port state before printing

option and the 

Spool MS-DOS print jobs

option, and

click on 

OK

. 

6.

Increase the 

Transmission retry

value of the Details tab

from 45 to 

900

. Click on 

OK

to close the Properties

window.

Quatro/510323 v3  1/8/99 11:37 AM  Page 36

Summary of Contents for Quatro Quatro ID Card Printer

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands