manualshive.com logo in svg

FARGO electronics Quatro Quatro ID Card Printer, User Manual

Share
Download
FARGO electronics Quatro Quatro ID Card Printer User Manual Download Page 28

24 Using the Quatro ID Card Printer  

card. Remember that all dye-sublimation prints must have
either the ribbonÕs overlay or a separate overlaminate applied
to them to prevent premature wear or fading.

Position

Select this feature to display options for adjusting the
placement of a cardÕs overall print area.

When adjusting the image placement, keep in mind that cards
always remain in the same position as they travel through the
printer. The diagram below represents how the printed image
will move in relation to the fixed card position as positive and
negative image placement values are entered. 

As you can see, the 

Vertical 

adjustment moves the image more

toward the rear of the printer if a positive number is entered
and more toward the front of the printer if a negative number
is entered. The 

Horizontal 

adjustment moves the image more

toward the card output side of the printer if a positive number
is entered and more toward the card input side of the printer if
a negative number is entered. The maximum value for either
adjustment is ±10.

Direction card travels through printer

+ Horizontal

Rear of Printer

Card Output

Side of Printer

- Horizontal

Card Input

Side of Printer

Front of Printer

- Vertical

+ Vertical

Quatro/510323 v3  1/8/99 10:48 AM  Page 24

Summary of Contents for Quatro Quatro ID Card Printer

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands