Fanvil VH05 User Manual Download

Page: 33 / 40

33 / 40

busy tone, ring-back tone, etc.

Handset Volume

Set the Handset volume, the value must be 1~9

Default Ring Type

Set the default ring type. If the caller ID of an incoming call was not

configured with specific ring type, the default ring will be used.

Speakerphone Volume

Set the speakerphone volume, the value must be 1~9

Headset Ring Volume

Set the ring volume in the headset, the value must be 1~9

Headset Volume

Set the Headset volume, the value must be 1~9

Speakerphone Ring Volume

Set the ring volume in the speakerphone, the value must be 1~9

Headset Volume Offset

This is to adjust the base volume of the headset. Please note when

set the volume at the maximum level it may create noise and

decrease the echo canceller.

Headset Mic Offset

This is to adjust the base volume of the headset Mic.

G.729AB Payload Length

Set G729 Payload Length.

G.723.1 Bit Rate

5.3kb/s or 6.3kb/s is available

G.722 Timestamps

160/20ms or 320/20ms is available

DTMF Payload Type

Enter the DTMF payload type, the value must be 96~127.

Enable VAD

Enable Voice Activity Detection. When enabled, the device will

suppress the audio transmission with artificial comfort noise signal

to save the bandwidth.

Enable MWI Tone

The phone will play MWI tone when a new MWI Comes

8.17 PHONE / MCAST

This feature allows user to make some kind of broadcast call to people who are in multicast group. User

can configure a multicast DSS Key on the phone, which allows user to send a Real Time Transport Protocol

(RTP) stream to the pre-configured multicast address(es) without involving SIP signaling. You can also

configure the phone to receive an RTP stream from pre-configured multicast listening address(es) without

involving SIP signaling. You can specify up to 10 multicast listening addresses.

Table 6 - MCAST Parameters on Web

Parameters

Description

Normal Call Priority

Define the priority of the active call, 1 is the highest priority, 10 is the

lowest.

Enable Page Priority

The voice call in progress shall take precedence over all incoming

paging calls.

Name

Listened multicast server name

Host:port

Listened multicast server’s multicast IP address and port.

Summary of Contents for VH05









































Search results

Summary of Contents for VH05

Reviews:

Related manuals for VH05

Brands by name

Popular brands

Fanvil VH05, User Manual

Search results

Summary of Contents for VH05

Reviews:

Related manuals for VH05

Brands by name

Popular brands