Fanvil i20S User Manual Download Page 7

Page: 7 / 50

[

键入文字

]

/ 50

II.

Start Using

Before you start to use the equipment, please make the following installation.

Confirm the connection

Confirm whether the equipment of the power cord, network cable, electric lock control line

connection and the boot-up is normal. (Check the network state of light)

Power, Electric Lock, Indoor switch port

Voice access the power supply ways: 12v/DC or POE.

CN7

+12V

VSS

COM

S_IN

S_OUT

12V 1A/DC

Electric-lock switch

Indoor switch

Driving mode of electric-lock(Default in active mode)

【

Note

】

When the device is in active mode, it can drive 12V/700mA switch output maximum, to which a

standard electric-lock or another compatible electrical appliance can be connected.



When using the active mode, it is 12V DC in output.



When using the passive mode, output is short control (normally open mode or normally close mode).

Jumper in passive mode

Jumper in active mode

Summary of Contents for i20S



















































Search results

Summary of Contents for i20S

Reviews:

Related manuals for i20S

Brands by name

Popular brands

Fanvil i20S, User Manual

Search results

Summary of Contents for i20S

Reviews:

Related manuals for i20S

Brands by name

Popular brands