Fantini Cosmi CH150RF Manual Download Page 23

23

turned on during the day.

Software revision and radio address

It displays the software revision for the unit in 
which the ambient temperature is usually in-
dicated, and also the radio address in which 
the three temperature T3, T2 and T1 are usu-
ally displayed. By pressing the 

 and 

 but-

tons simultaneously for more than 4 seconds, 
you can change the programmable thermostat 
radio address. Following this procedure, the 
radio actuators previously registered shall be 
con

fi

 gured again (refer to the <<Actuator reg-

istration>> chapter).

Actuator registration

Prior to starting up the system, the radio ac-
tuators shall be registered to the CH150RF, 
CH151RF, CH152RF programmable thermo-
stat. To avoid memorizing a code belonging to 
another programmable thermostat, the recep-
tion sensitivity during the con

fi

 guration proce-

dure is reduced; therefore, the programmable 
thermostat and the actuator should be posi-
tioned at a distance of less than 2 m. Moreo-
ver, you should verify that the radio socket is 

correctly connected with the programmable 
thermostat (refer to Index 1 of the con

fi

 guration 

menu, <<Programmable thermostat con

fi

 gura-

tion>> chapter).

Heating system actuator registration:

1. Set the actuator to the “system code self-
learning” mode (refer to the actuator instruc-
tion sheet).
2. Send the heating system actuator registra-
tion radio control (refer to index 2 of the con-

fi

 guration menu, <<Programmable thermostat 

con

fi

 guration>> chapter):

2A. Press SET / PROG [button 6]. The oper-
ating mode currently used will be temporarily 
interrupted.
2B. Keep the SUMMER / WINTER switching 
button [button 10] depressed for approximately 
5 seconds, to display the initial page of the pro-
gramming menu.
2C. Press 

 [button 4] to select the second 

parameter (the “rF t” message will appear on 
the display; the displayed index will be number 
2).
2D. Press 

 [button 1] to send the heating 

system actuator registration radio control. The 
“rF t” message will blink: verify that the actua-
tor is registered after a few seconds.

voltar.com.ua

voltar.com.ua

voltar.com.ua

voltar.com.ua

voltar.com.ua

voltar.com.ua

voltar.com.ua

voltar.com.ua

voltar.com.ua

Summary of Contents for CH150RF

































Reviews: