Fantek T-104 Operating Instructions Manual Download Page 23

3.18.-  For  transportation  it  is  necessary  to  retract  all  profiles  and  lock  them  with  the 

adjustment knobs. 

4. Operation

4.1.- Place the tower on a flat and solid surface in its site of operation. 

4.2.-  Pull  the  legs  out  of  their  support  for  transport  (S)  and  insert  them  in  their  working 

lodges  (V).  Check  that  they  are  fully  inserted  and  fastened  by  the  retaining  safety 

triggers (R). 

SEE FIGURE 1. 

4.3.- Adjust the vertical alignment of the tower with the support plates (Q) by turning the 

handle (H) in the required sense until the bubble of the level (F) becomes centered in 

the circle. When leveling the tower, the transport wheels must have firm contact with 

the ground as another supporting point. 

SEE FIGURE 2. 

4.4.- Release the adjustment knob of the third profile. Attach the load to the tower using 

an  adequate  support  (this  may  vary  according  to  the  situation),  so  that  it  can  move 

only  in  a  vertical  sense.  The  minimum  load  must  be  25  kg  and  will  be  blocked 

automatically in any position by the retention system. 

SEE FIGURE 3. 

4.5.- Up: 

Turn  the  winch  handle  (W)  clockwise  (N1)  to  lift  the  load  up  to  the  required  position, 

then  check  that  the  automatic  triggers  are  locked  in  so  that  the  profiles  are  fixed 

automatically.  The  safety  triggers  must  always  stay  locked  at  the  end  of  the  lifting 

process (1). This is achieved by descending the load by some centimetres once it has 

reached its required position. 

As the profiles extend, you must fix them with the adjustment knobs before releasing the 

next profile (2). 

As is shown in the previous picture, you must first secure the correct setting of the safety 

trigger (1), only then the following adjustment knob will be released (2). 

SEE FIGURE 4. 

4.6.- Continue elevating: 

Turn the winch handle (W) again clockwise and lift the load until the second profile is 

fully  extended.  Release  the  handle  which  will  remain  fixed  by  the  winch's  automatic 

brake  and  lock  the  second  profile  with  the  nearest  safety  trigger  and  press  the 

adjustment knob to eliminate the play between the profiles. 

SEE FIGURE 5. 

4.7.- Down: 

Release the adjustment knob of the profile that was lifted last (step 1). Then release the 

safety trigger (M1) (step 2). To release the safety triggers, it is necessary to lift the load 

slightly with the winch and then release them. In the normal working position the weight 

of  load  makes  it  impossible  to  free  the  safety  triggers.  Having  unlocked  the  safety 

trigger (M1), turn the winch handle counterclockwise (N2) to descend the load until the 

first profile is at its bottom position (step 3). 

Summary of Contents for T-104









































Reviews: