www.fanox.com
Rev. 01
2/17
1.
MODBUS RTU PROTOCOL ............................................................................................ 3
1.1.
Modbus RTU pachage format ........................................................................................ 4
1.2.
Function Codes............................................................................................................... 4
1.3.
Exceptions Responses .................................................................................................. 5
1.4.
Data type .......................................................................................................................... 5
1.5.
General Memory Map ..................................................................................................... 7
1.5.1.
States Map ................................................................................................................... 7
1.5.2.
Measurements Map .................................................................................................... 12
1.5.3.
Settings Map .............................................................................................................. 12
1.6.
Command List ............................................................................................................... 16
1.7.
Setting-up the session: Password and access levels .............................................. 16
1.8.
Example of Modbus Frames ........................................................................................ 16
