Fanimation LP8147SLBL Manual Download Page 2

Important Safety Instructions

WARNING:

To avoid fire, shock and serious personal injury, follow these instructions.

1. Read  your  owner’s  manual  and  safety  information  before  installing  your  new  fan.  Review  the  accompanying  assembly

diagrams.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent

power  from  being  switched  on  accidentally.  When  the  service  disconnecting  means  cannot  be  locked,  securely  fasten  a
warning device, such as a tag, to the service panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling

fan before servicing.

4. Do not insert anything into the fan blades while the fan is operating.

Additional Safety Instructions

1. To  avoid  possible  shock,  be  sure  electricity  is  turned  off  at  the  fuse  box  before  wiring,  and  do  not  operate  fan  without

blades.

2. All  wiring  and  installation  procedures  must  satisfy  National  Electrical  Codes  (ANSI/  NFPA  70)  and  Local  Codes.  The

ceiling  fan  must  be  grounded  as  a  precaution  against  possible  electrical  shock.  Electrical  installation  should  be  made  or
approved by a licensed electrician.

3. The  fan  base  must  be  securely  mounted  and  capable  of  reliably  supporting  at  least 35 lbs.  (fan  and  accessories  not  to

exceed 35  lbs.  or 15.88  kgs.).  See  page  5  of  owner’s  manual  for  support  requirements.  Consult  a  qualified  electrician  if  in
doubt.

4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.
5. Follow  the  recommended  instructions  for  the  proper  method  of  wiring  your  ceiling  fan.  If  you  do  not  have  adequate

electrical knowledge or experience, have your fan installed by licensed electrician.

6. Suitable for use with solid-state speed controls.

W A R N I N G :

TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE, 

ISOLATING WALL CONTROL/SWITCH.

WARNING:

This  product  is  designed  to  use  only  those  parts  supplied  with  this  product  and/or  accessories  designated

specifically for use with this product. Using parts and/or accessories not designated for use with this product could result in
personal injury or property damage.

WARNING:

To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the

WARNING:

Mount to an outlet box marked acceptable for fan support.

brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation. If the intentional radiator can be classified as a Class B digital device or a PC 
peripheral, then shall include the following or equivalent:

Note:

 This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the 

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna. 
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. 

Note:

 For a Class A digital device, statements of 15. 105(a) must be included when appropriate for the device in question.

5. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be 

supervised to ensure that they do not play with the appliance.

8. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be connected to a 
grounded conductor power supply. If the conductor of a fan is identified as an ungrounded conductor, then it should be 
connected to an ungrounded conductor power supply. If the conductor of a fan is identified for equipment grounding, then it 
should be connected to an equipment-grounding conductor.

WARNING:

Do not operate this fan with a variable (Rheostat) wall controller or dimmer switch. Doing so could result in damage 

to the ceiling fan's remote control unit.

7. This fan is to be used in dry and damp locations.

CAUTION:

 

Changes or modifications not expressly approved by the party responsible for compliance could void the user's 

authority to operate the equipment.

WARNING: 

Chemical Burn Hazard. Keep batteries away from children.

9. The remote control of this product contains lithium button/coin cell batteries. If a new or used lithium button/coin cell battery  
is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always 
completely secure the battery compartment. If the battery compartment does not close securely, stop using the remote control 
of the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed 
inside any part of the body, seek immediate medical attention.

The cells shall be disposed of properly, including keeping them away from children.

Even used cells may cause injury.

Summary of Contents for LP8147SLBL









































Reviews: