F&U FLS32211H, Instruction Book

Page: 9 / 63

English - 8 -
Switching On/Off
To Switch the TV On
Connect the power cord to a power source such as a wall
socket (220-240V AC, 50 Hz).
To switch on the TV from standby mode either:
• Press the
Standby button, Pro/- or a numeric
button on the remote control.
• Press the the middle of side function switch on the TV in.
To Switch the TV Off
Press the Standby button on the remote control or press
the middle of the side function switch on the TV in and
hold it down for a few seconds, the TV will switch into
standby mode.
To power down the TV completely, unplug the power
cord from the mains socket.
Note: When the TV is switched into standby mode, the standby
LED can blink to indicate that features such as Standby Search,
Over Air Download or Timer is active. The LED can also blink
when you switch on the TV from standby mode.
First Time Installation
When turned on for the first time, the language selection
screen is displayed. Select the desired language and
press OK .
On the next screen, set your preferences using the
directional buttons.
Note: Depending on the Country selection you may be asked
to set and confirm a PIN at this point. The selected PIN cannot
be 0000. You have to enter it if you are asked to enter a PIN for
any menu operation later.
About Selecting Broadcast Type
Digital Aerial: If Digital Aerial broadcast search option
is turned on, the TV will search for digital terrestrial
broadcasts after other initial settings are completed.
Digital Cable: If Digital Cable broadcast search option is
turned on, the TV will search for digital cable broadcasts
after other initial settings are completed. According to
your other preferences a confirmation message may
be displayed before starting to search. Select YES and
press OK to proceed. To cancel operation, select NO and
press OK . You can select Network or set values such
as Frequency , Network ID and Search Step . When
finished, press OK button.
Note:
Searching duration will change depending on the selected
Search Step .
Satellite: If Satellite broadcast search option is turned
on, the TV will search for digital satellite broadcasts after
other initial settings are completed. Before satellite search
is performed some settings should be made. Antenna
Type menu will be displayed first. You can select Antenna
Type as Direct , Single Satellite Cable or DiSEqC switch
by using “ ” or “ ” buttons.
• Direct: If you have a single receiver and a direct satellite
dish, select this antenna type. Press OK to continue.
Select an available satellite on the next screen and press
OK to scan for services.
• Single Satellite Cable: If you have multiple receivers
and a single satellite cable system, select this antenna
type. Press OK to continue. Configure settings by
following instructions on the next screen. Press OK to
scan for services.
• DiSEqC switch:
If you have multiple satellite dishes
and a
DiSEqC switch
, select this antenna type. Press
OK
to continue. You can set four
DiSEqC
options (if
available) on the next screen. Press OK button to scan
the first satellite in the list.
Analogue: If Analogue broadcast search option is turned
on, the TV will search for analogue broadcasts after other
initial settings are completed.
Additionally you can set a broadcast type as your favourite
one. Priority will be given to the selected broadcast type
during the search process and the channels of it will be
listed on the top of the Channel List . When finished,
press OK to continue.
You can activate
Store Mode
option at this point.
This option will configure your TV’s settings for store
environment and depending on the TV model being
used, the supported features of it may be displayed on
the top of the screen as an info banner. This option is
intended only for store use. It is recommended to select
Home Mode for home use. This option will be available
in System>Settings>More menu and can be turned
off/on later.
Press
OK button on the remote control to continue and
the Network/Internet Settings menu will be displayed,
if you confirm the previously displayed message asking
whether you want to do the network settings. Please refer
to Connectivity section to configure a wired or a wireless
connection. After the settings are completed press OK
button to continue. To skip to the next step without doing
anything select No and press the OK button when the
message is displayed asking whether you want to do the
network settings.
After the initial settings are completed TV will start to
search for available broadcasts of the selected broadcast
types.
After all the available stations are stored, scan results will
be displayed. Press OK to continue. The Edit Channel
List menu will be displayed next. You can edit the channel
list according to your preferences or press the Menu
button to quit and watch TV.
While the search continues a message may appear,
asking whether you want to sort channels according to
the LCN (*) . Select Yes and press OK to confirm .
(*) LCN is the Logical Channel Number system that organizes
available broadcasts in accordance with a recognizable channel
number sequence (if available).
Note:
Do not turn off the TV while initializing first time installation.
Note that, some options may not be available depending on the
country selection.