background image

REMOTE PAIRING INSTRUCTIONS 

 

 

Rev 6.0

 

Fanco Infinity DC. All Rights Reserved.

 

 

HOW TO PERFORM A MANUAL ID CODE LEARNING PROCESS 

 

A remote receiver must undergo an “ID code learning” process before it 

recognises and is able to 

communicate with remote transmitter before you use it for the first time. You do not have to pair the 
receiver every time you use the fan. 

You will also 

be required to perform an “ID code learning” process manually if:

 

 

Your remote controller is not responding or if you are getting a new replacement for 

transmitter/receiver.  

 

You have 2 or more ceiling fans of the same model in one or nearby location, and you wish to 

be able to control each fan independently without affecting operation of the other fans. 

 

You have 2 or more ceiling fans of the same model and you wish to control by one remote 
handset. 

INSTRUCTION:

 

IF USING INDIVIDUAL REMOTE CONTROLLER FOR EACH INDEPENDENT FAN

   

1.

 

Turn OFF the power to each receiver of ALL fans in the same or nearby location. Electrician 

MUST

 install all poles disconnection / isolation wall switch in the fixed wirings for each fan.

 

2.

 

Turn ON 

ONLY

 the power to the receiver of each fan per time. DO NOT TURN ON THE POWER 

FOR ALL OTHER FANS. 

3.

 

Press the 

“STOP”

 

& “LIGHT OFF”

 buttons and hold both buttons for over 5 seconds.  

4.

 

The receiver will beep once it has detected the new code setting. Beeping indicates the code 

learning process has been completed. 

5.

 

Try different speed setting on remote handset to ensure the fan is now fully functional. If not, 
repeat the process starting from STEP 1 again.

 

 

INSTRUCTION:

 

IF USING ONE REMOTE CONTROLLER FOR MULTIPLE FANS

   

1.

 

Turn OFF the power to each receiver of ALL fans in the same or nearby location. Electrician 
MUST install all poles disconnection / isolation wall switch in the fixed wirings for each fan.

 

2.

 

Turn ON the power to all receivers for all fans.  

3.

 

Press the “STOP”

 

& “LIGHT OFF”

 buttons and hold both buttons for over 5 seconds.  

4.

 

The receiver will beep once it has detected the new code setting. Beeping indicates the code 

learning process has been completed. 

5.

 

If all the other fans are out of range, repeat STEP 1 to STEP 3 using the same remote handset.  

6.

 

Try different speed setting on remote handset to ensure all fans are now fully functional. If not, 
repeat the process starting from STEP 1 again.

 

 
 
 
 
 
 

Summary of Contents for INFINITY i DC Series

















Reviews: