Fanaway Montclair Installation Instructions Manual Download Page 11

Fanaway Montclair Installation Instructions

 

 

 

11  | 

P a g e                                                                 M O N T C L A I R  

                                        V e r s i o n 1 . 0   0 1 / 2 0 2 0    

AFTER INSTALLATION

 

WOBBLE: 

NOTE:  ceiling  fans  tend  to  move  during  operation  due  to  the  fact  that  they  are  mounted  on  a  rubber 

grommet. If the fan was mounted rigidly to the ceiling it would cause excessive vibration. Movement of a 

few centimetres is quite acceptable and DOES NOT suggest any problem.   

TO  REDUCE  THE  FAN  WOBBLE:

  Please  check  that  all  screws  which  fix  the  mounting  bracket  and 

down rod are secure. 

NOISE: 

When it is quiet (especially at night) you may hear occasional small noises. Slight power fluctuations and 

frequency signals superimposed in the electricity for off-peak hot water control, may cause a change in 

fan motor noise. This is normal. Please allow a 24-

hour “breaking -in” period, most noises associated 

with a new fan disappear during this time. All electric motors are audible to some extent. Please note 

that this is not a product fault, and as such is not covered under warranty. 

 

CARE & CLEANING

 

NOTE:  Always  turn  OFF  the  power  at  the  mains  switch  before  performing  any  maintenance  or 

attempting to clean your fan. 

1)  Every  6 months periodic cleaning of your ceiling fan is the only maintenance required. Use a soft 

brush or lint free cloth to avoid scratching the paint finish. Please turn OFF electricity power when 

you do so. 

2)  Do not soak or immerse your ceiling fan in water or other liquids. It could damage the motor or the 

blades and create the possibility of an electrical shock. 

3)  Ensure that the fan does not come in contact with any organic solvents or cleaners. 

4)  To clean the fan blade, wipe with only a damp clean cloth with NO organic solvents or cleaners. 

5)  The motor has a permanently lubricated ball bearing so there is no need to oil. 

 

TECHNICAL INFORMATION

 

Fan Size

 

Speed

 

Volts 

V

 

Amps 

(A) 

Watts 

(W)

 

RPM

 

CFM

 

CFM/

W

 

N.W. 

(lbs)

 

G.W. 

(lbs)

 

C.F.

 

BI-48" 

FAN-MOXX

X-USA-FA 

 

Extra-High 

120 

0.47 

56.36W 

207 

4172.69 

74.03 

26.68 

31.31 

5.05 

Medium 

High 

120

 

0.36 

32.59W 

160 

3029.29 

92.95 

26.68 

31.31 

5.05 

Low 

120

 

0.27 

19.37W 

119 

2115.13 

109.19 

26.68 

31.31 

5.05 

 

These are approximate measurements. They do not include data for any lamps or fixtures attached to 

the ceiling fan. 

 

WARRANTY

 

 

1 year warranty covers the entire fan. Please refer to warranty card for the details. 

Summary of Contents for Montclair























Reviews: