background image

Fanaway EVO1 LED Installation Instructions 

 

 

 

2 | 

P a g e

 

 

all-pole safety switch at the switchboard, then this is considered to be 

an  all-pole  disconnection  to  the  ceiling  fan  electrical  circuit,  meeting 

the requirements of clause 7.12.2 of AS/NZS 60335.1.   

A single-pole switch on the active of the receiver input of remote 

control must also be included in the wiring, and located the same 

room as the ceiling fan.

 

 

5. 

  Do not dispose of electrical appliances as unsorted municipal waste, use separate collection 

facilities. Contact your local government for information regarding the collection systems available. If 

electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the 

ground water and get into the food chain, damaging your health and well-being. 

6.  The structure to which the fan is to be mounted must be capable of supporting a weight of 50kg. 

7.  The fan should be mounted so that the blades are at least 2.3 m above the floor in Europe or 2.1 m 

above the floor in Australia.   

8.  This fan is 

suitable 

for indoor use only. Mounting the fan in a location where it is subject to water or 

moisture is dangerous and 

may increase the risk of damage, injury or electrical shock 

and will void 

the warranty. 

9.  Must be assembled and installed by a licensed electrician. 

10.  WARNING:  If  unusual  wobbling  or  oscillating  movement  is  observed,  immediately  stop  using  the 

ceiling fan and contact the manufacturer, its service agent or suitably qualified persons. 

11.  The  replacement  of  parts  of  the  safety  suspension  system  device  shall  be  performed  by  the 

manufacturer, its service agent or suitably qualified persons. 

12.  The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a 

sufficient  strength  to  withstand  4  times  the  weight  of  the  ceiling  fan;  that  the  mounting  of  the 

suspension system shall be performed by the manufacturer, its service agent or suitably qualified 

persons. 

13.  The light source contained in this luminaire shall only be replaced by the manufacturer or his service 

agent or a similar qualified person. 

 

Summary of Contents for EVO1 - PREVAIL
















Reviews: