background image

9.0  Definitions

The following are general definitions of fall protection terms as defined by ANSI Z359.0-2012.

Anchorage -

A secure connecting point or a terminating component of a fall protection system or rescue system 

capable of safely supporting the impact forces applied by a fall protection system or anchorage subsystem.

Anchorage Connector -

 A component or subsystem that functions as an interface between the anchorage and 

a fall protection, work positioning, rope access or rescue system for the purpose of coupling the system to the 

anchorage.

Arrest Distance - 

The total vertical distance required to arrest a fall. The arrest distance includes the deceleration 

distance and activation distance.

Authorized Person –

 A person assigned by the employer to perform duties at a location where the person will be 

exposed to a fall hazard.

Available Clearance -

 The distance from a reference point, such as the working platform, to the nearest 

obstruction that an authorized person might contact during a fall which, if struck, could cause injury.

Capacity - 

The maximum weight that a component, system or subsystem is designed to hold.

Certification - 

The act of attesting in writing that the criteria established by these standards or some other 

designated standard have been met.

Certified Anchorage -

 An anchorage for fall arrest, positioning, restraint or rescue systems that a qualified person 

certifies to be capable of supporting the potential fall forces that could be encountered during a fall.

Clearance - 

The distance from a specified reference point, such as the working platform or anchorage of a fall 

arrest system, to the lower level that a worker might encounter during a fall.

Clearance Requirement - 

The distance below an authorized person that must remain clear of obstructions in 

order to ensure that the authorized person does not make contact with any objects that would cause injury in the 

event of a fall.

Competent Person - 

An individual designated by the employer to be responsible for the immediate supervision, 

implementation and monitoring of the employer’s managed fall protection program who, through training and 

knowledge, is capable of identifying, evaluating and addressing existing and potential fall hazards, and who has 

the employer’s authority to take prompt corrective action with regard to such hazards.

Component - 

An element or integral assembly of interconnected elements intended to perform one function in 

the system.

Confined Space - OSHA defines a Confined Space as:

• 

Is large enough for an employee to enter fully and perform assigned work;

• 

Is not designed for continuous occupancy by the employee; and

• 

Has a limited or restricted means of entry or exit.

Connecting Subsystem - 

An assembly, including the necessary connectors, comprised of all components, 

subsystems, or both, between the anchorage or anchorage connector and the harness attachment point.

Connector -

 A component or element that is used to couple parts of the system together.

Deceleration Distance - 

The vertical distance between the user’s fall arrest attachment at the onset of fall arrest 

forces during a fall, and after the fall arrest attachment comes to a complete stop.

Energy (Shock) Absorber -

 A component whose primary function is to dissipate energy and limit deceleration 

forces which the system imposes on the body during fall arrest.

Fall Arrest - 

The action or event of stopping a free fall or the instant where the downward free fall has been 

stopped.

Fall Hazard - 

Any location where a person is exposed to a potential free fall.

Free Fall -

The act of falling before a fall protection system begins to apply forces to arrest the fall.

Free Fall Distance -

 The vertical distance traveled during a fall, measured from the onset of a fall from a walking 

working surface to the point at which the fall protection system begins to arrest the fall.

Harness, Full Body - 

A body support designed to contain the torso and distribute the fall arrest forces over at least 

the upper thighs, pelvis, chest and shoulders.

Horizontal Lifeline –

 A component of a horizontal lifeline subsystem, consisting of a flexible line with connectors 

or other coupling means at both ends for securing it horizontally between two anchorages or anchorage 

connectors.

MFBH04 Rev A

121219

12

http://www.bestmaterials.com      |      1-800-474-757

0

[email protected]    |      

http://www.bestmaterials.com      |      1-800-474-7570

     [email protected]    |      http://www.bestmaterials.com      |      1-800-474-7570

http://www.bestmaterials.com      |      1-800-474-757

0

[email protected]    |      

http://www.bestmaterials.com      |      1-800-474-7570

      [email protected]    |      http://www.bestmaterials.com      |      1-800-474-7570

         

Distributed by Best Materials® LLC

Summary of Contents for 7083B

























Reviews: