background image

5

4

a.  Turn baseplate assembly upside down so pushpad is 

resting on a flat surface and motor mounting location is on 

the left. 

 

pushpad

motor mounting 

location

b.  Place motor in left hand with LED status sticker facing 

toward you. Gently extend silver hook arm outward (about 

Z\x

”) until you meet some resistance, then hold.

LED 

status 

sticker

b

c.  While tilting baseplate assembly away from you slightly, 

move extended hook arm into position under baseplate. A 

post will be hanging down from baseplate; the hook arm 

should sit on the near side of that post. Rotate the motor 

assembly to hook the arm over the baseplate axle pin that 

is closest to the baseplate. Do not pull out on motor at this 

step. 

post

pin

90°

d. 

Set motor on flat surface. 

e. 

Push down firmly on baseplate so it bottoms out against 

push pad. 

f.  While depressing baseplate, lift up motor assembly and 

guide it along elongated baseplate slot until motor lip slips 

over baseplate. 

e

f

Lip slips over baseplate

g.  Release baseplate. Secure motor assembly with 2 small 

self-tapping screws (provided). 

Use #1 Phillips

screwdriver

h.  Turn baseplate and motor assembly right side up.        

Secure motor assembly

Summary of Contents for MEL 24 Series













Reviews: