background image

G7204, G7208

and G7211 FORCED

CONVECTION OVENS

INSTALLATION and

SERVICING INSTRUCTIONS

These Appliances must be installed and serviced by a competent person as stipulated by the Gas

Safety (Installation & Use) Regulations.

IMPORTANT
The installer must ensure that the installation of the appliance is in conformity with these instructions and

National Regulations in force at the time of installation. Particular attention MUST be paid to -

I.E.E Regulations for Electrical Installations
Electricity At Work Regulations
Gas Safety (Installation & Use) Regulations
Health And Safety At Work etc. Act
Local and National Building Regulations
Fire Precautions Act

These Appliances have been CE-marked on the basis of compliance with the Gas Appliance Directive, EMC

and Low Voltage Directive for the countries, Gas Types and Pressures as stated on the Data Plate.

WARNING - TO PREVENT SHOCKS, ALL APPLIANCES WHETHER

GAS OR ELECTRIC, MUST BE EARTHED

On completion of the installation, these instructions should be left with the Engineer-in-Charge for reference

duringservicing. Further to this, The Users Instructions should be handed over to the User, havinghad a

demonstration of the operation and cleaningof the appliance.

IT IS MOST IMPORTANT THAT THESE INSTRUCTIONS BE CONSULTED BEFORE INSTALLING AND

COMMISSIONING THIS APPLIANCE. FAILURE TO COMPLY WITH THE SPECIFIED PROCEDURES MAY

RESULT IN DAMAGE OR THE NEED FOR A SERVICE CALL.

PREVENTATIVE MAINTENANCE CONTRACT
In order to obtain maximum performance from this unit we would recommend that a Maintenance Contract be

arranged with SERVICELINE. Visits may then be made at agreed intervals to carry out adjustments and

repairs. A quotation will be given upon request to the contact numbers below.

WEEE Directive Registration No. WEE/DC0059TT/PRO
At end of unit life, dispose of appliance and any replacement parts

in a safe manner, via a licenced waste handler.
Units are designed to be dismantled easily and recycling of all

material is encouraged whenever practicable.

T100635 Ref. 2

Falcon Foodservice Equipment

HEAD OFFICE AND WORKS
Wallace View, Hillfoots Road, Stirling. FK9 5PY. Scotland.
SERVICELINE CONTACT -
PHONE - 01438 363 000

FAX - 01438 369 900

Detailed recommendations are contained in

Institute of Gas Engineers published

documents :
IGE/ UP/ 1, IGE/ UP/ 2, BS6173 and BS5440

All manuals and user guides at all-guides.com

Summary of Contents for G7204













Reviews: