background image

E7204, E7208 and E7211  
Forced Convection Ovens 
 

CAUTION: Read the instructions before  
using the appliance. 

 

INSTALLATION and SERVICING  
INSTRUCTIONS 
 

IMPORTANT 

The installer must ensure that the installation of the appliance is in conformity with these 
instructions and National Regulations in force at the time of installation. Particular attention 
MUST be paid to 

– 

BS7671 IEE Wiring Regulations 
Electricity at Work Regulations 
Health And Safety At Work Act 
Fire Precautions Act 

This appliance has been CE-marked on the basis of compliance with the Low Voltage and EMC 
Directives for the voltages stated on the Data Plate 
 

WARNING -THIS APPLIANCE MUST BE EARTHED 
 

On completion of the installation these instructions should be left with the Engineer-in-Charge for 
reference during servicing. Further to this, The Users Instructions should be handed over to the 
User, having had a demonstration of the operation and cleaning of the appliance.  
 

IT IS MOST IMPORTANT THAT THESE INSTRUCTIONS BE CONSULTED BEFORE 
INSTALLING AND COMMISSIONING THIS APPLIANCE. FAILURE TO COMPLY WITH THE 
SPECIFIED PROCEDURES MAY RESULT IN DAMAGE OR THE NEED FOR A SERVICE 
CALL. 
 
PREVENTATIVE MAINTENANCE CONTRACT 

In order to obtain maximum performance from this unit we would recommend that a Maintenance 
Contract be arranged with SERVICELINE. Visits may then be made at agreed intervals to carry 
out adjustments and repairs. A quotation will be given upon request to the contact numbers 
below. 

      WEEE Directive Registration No. WEE/DC0059TT/PRO 
 

At end of unit life, dispose of appliance and any replacement parts in a safe 
manner, via a licensed waste handler. 

     Units are designed to be dismantled easily and recycling of all material is    
     encouraged whenever practicable. 

 

Falcon Foodservice Equipment

 

Head Office and Works 
Wallace View, Hillfoots Road, Stirling. FK9 5PY. Scotland. 
Serviceline

PHONE : 01438 363 000   

 

Warranty Policy Shortlist 
 

Warranty does not cover :- 
Correcting faults caused by incorrect installation of a product. 
Where an engineer cannot gain access to a site or a product. 

T100683 Ref.5 

Summary of Contents for E7204














Reviews: