Fagor CNC 8070, Programming Manual

Page: 400 / 556

‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
Programming manual
402
CNC 8070
14.
CNC VARI
ABLES
Rel
a
te
d
t
o
gener
al
m
a
ch
in
e pa
ra
m
e
te
rs
(S
OFT
V02.0
X
)
366
14.2.1 Channel related
These variables are read-only (R) synchronous and are evaluated execution time.
They have generic names.
• Replace the "n" character with the channel number, maintaining the brackets. The first
channel is identified with the number 1, "0" is not a valid number.
• Replace the "x" letter with the axis number.
PLC reading of CIRINFACT and MAXOVR comes in tenths (a reading of 10 for 1%) Ver "Access to
numeric values from the PLC" en la página 358.
(V.)[n].MPG.GROUPID V.[1].MPG.GROUPID V.[2].MPG.GRUOPID
(V.)[n].MPG.CHAXISNAMEx V.[2].MPG.CHAXISNAME2 V.[1].MPG.CHAXISNAME3
CHANNEL CONFIGURATION
PRG PLC INT
(V.)[n].MPG.GROUPID Group the channel belongs to R R R
(V.)[n].MPG.CHTYPE Channel type
"0" = CNC "1" = PLC "2" = CNC+PLC
R R R
(V.)[n].MPG.HIDDENCH Hidden channel
"0" = No "1"= Yes
R R R
CONFIGURING THE AXES OF THE CHANNEL
PRG PLC INT
(V.)[n].MPG.CHNAXIS Number of axes of the channel R R R
(V.)[n].MPG.CHAXISNAMEx Name of the "n" logic axis — — R
CONFIGURING THE SPINDLES OF THE CHANNEL
PRG PLC INT
(V.)[n].MPG.CHNSPDL Number of spindles of the channel R R R
(V.)[n].MPG.CHSPDLNAMEx Name of the "x" spindle — — R
(V.)[n].MPG.CAXNAME Axis working as "C" axis (by default) — — R
(V.)[n].MPG.ALIGNC "C" axis in diametrical machining
"0" = No "1"= Yes
R R R
TIME SETTING (CHANNEL)
PRG PLC INT
(V.)[n].MPG.PREPFREQ Number of blocks to prepare per cycle R R R
(V.)[n].MPG.ANTIME Anticipation time R R R
DEFAULT CONDITIONS
PRG PLC INT
(V.)[n].MPG.KINID Default kinematics number R R R
(V.)[n].MPG.SLOPETYPE Default acceleration type
"1" = Linear "2" = Trapezoidal "3" = Square sine
R R R
(V.)[n].MPG.IPLANE Default work plane
"0" = G17 "1" = G18
R R R
(V.)[n].MPG.ISYSTEM Default programming type
"0" = G90 "1" = G91
R R R
(V.)[n].MPG.IMOVE Default movement type
"0" = G00 "1" = G01
R R R
(V.)[n].MPG.IFEED Default feedrate type
"0" = G94 "1" = G95
R R R
(V.)[n].MPG.ICORNER Default corner type
"0" = G50 "1" = G05 "2" = G07
R R R
(V.)[n].MPG.IRCOMP Radius compensation mode by default
"0" = G136 "1" = G137
R R R
(V.)[n].MPG.ROUNDTYPE Rounding type in G5 (by default)
"0" = Chordal error "1" = %feedrate
R R R
(V.)[n].MPG.MAXROUND Maximum rounding error in G5 R R R
(V.)[n].MPG.ROUNDFEED Percentage of feedrate in G5 R R R
(V.)[n].MPG.CIRINERR Absolute radius error R R R
(V.)[n].MPG.CIRINFACT Percentage of error over the radius R R R
(V.)[n].MPG.MAXOVR Maximum axis override (%) R R R
(V.)[n].MPG.RAPIDOVR Override affecting G00
"0" = No "1"= Yes
R R R