background image

14

1: Site Selection and Planning

It’s important to choose the best roof loca-

tion to install the solar collectors, based on the           

considerations below: 

Roof Direction

For  homes  in  the  northern  hemisphere,  the  best 

installation site is a roof facing true south. (See Figure 4.)  

If a south-facing roof isn’t available, then choose a site 

based on the following:

•  Second choice, a roof facing between southeast and 

southwest

•  Third choice, a roof facing West or East

Distance From Water Heater

The solar collectors should be as close as possible to 

the water heater. The closer the collectors are to the 

water  heater,  the  shorter  the  tubing  run  will  be.  The 

maximum  allowable  vertical  height  of  the  collectors 

from the drainback tank is 15 feet with a medium head 

circulation module and 30’ with a high head circulation 

module.    The  maximum  required  tubing  length  each 

way  to  the  solar  collectors  is  100’.  The  Solar  Water 

Heating  System  comes  with  80’  of  tubing. Additional 

tubing may be ordered from your dealer.  

Mounting Methods by Roof Type

The following are recommendations for mounting to vari-

ous roof types. Consult a roofing professional regarding 

the correct method for installing solar panels on a roof. 

Inspect the condition of the roof. Contact a roofing pro-

fessional to determine the remaining life of the roof be-

fore recommended replacement.

Important: The solar collectors are flexible and must be installed 

on a smooth, flat surface. Any uneven or very rough roof surface 

will require a flat support surface underneath the solar collectors. 

Composition asphalt

This is a common roof type, and solar collectors can be 

mounted directly to the roof. Refer to the instructions on 

the following pages detailing mounting on composition 

asphalt. (See Figure 5.)

Shake 

A substrate must be used on shake roofs.

 Mount solar collec-

tors directly on top of the substrate. Lay substrate on roof 

and proceed with the standard mounting procedures on 

the following pages.  UV resistant, dark color, 2’ wide by 

Figure 4 - Roof Direction

Shading  from  trees  or  other  buildings  should  be 

avoided between 10am to 3pm. Keep in mind that as 

the seasons change, the sun changes its trajectory in 

the  sky.  The  sun  appears  higher  during  the  summer 

months  and  lower  in  the  southern  sky  during  winter 

months. Areas  that  are  clear  in  the  summer  may  be 

shaded by tree and shrub growth in the winter.  

Roof Size

Collectors must be mounted vertically, perpendicular 

to the shingle rows, as shown in Figure 5.  

•  One set of (3) 2’ x 8’ solar collectors will need a clear 

roof area measuring at least 7.5’ wide x 9’ tall.

•  One set of (2) 2’ x 12’ solar collectors will need a 

clear roof area measuring at least 5.5’ wide x 13’ tall.

Figure 5 - Composition Asphalt Roof

Summary of Contents for Drainback 200 Series



































Reviews: