2
CORAL
GENERAL WARNINGS FOR PEOPLE SAFETY
THANK YOU
Thank you for purchasing a Fadini product.
Please read these instructions carefully before using this
appliance. The instructions contain important information
which will help you get the best out of the appliance and
ensure safe and proper installation, use and maintenance.
Keep this manual in a convenient place so that you can always
refer to it for the safe and proper use of the appliance.
INTRODUCTION
This operator is designed for a speci c scope of applications as
indicated in this manual, including safety, control and signaling
accessories as minimum required with Fadini equipment.
□
Any
applications not explicitly included in this manual may cause
operation problems or damages to properties and people.
□
Meccanica Fadini snc is not liable for damages caused by the
incorrect use of the equipment, or for applications not included
in this manual or for malfunctioning resulting from the use of
materials or accessories not recommended by the
manufacturer.
□
The manufacturer reserves the right to make
changes to its products without prior notice.
□
All that is not
explicitly indicated in this manual is to be considered not
allowed.
BEFORE INSTALLATION
Before commencing operator installation assess the suitability
of the access, its general condition and the structure.
□
To
check that the ground is stable, to avoid subsequent settling or
deformation in the traffic control post installation area.
□
Make
sure that there is no risk of impact, crushing, shearing,
conveying, cutting, entangling and lifting situations, which
may prejudice people safety.
□
Do not install near any source of
heat and avoid contacts with ammable substances.
□
Keep all
the accessories able to turn on the operator (transmitters,
proximity readers, key-switches, etc) out of the reach of the
children.
□
Transit through the access only with stationary
operator.
□
Do not allow children and/or people to stand in the
proximity of a working operator.
□
To ensure safety in the
whole movement area of a bollard it is advisable to install
photocells, sensitive edges, magnetic loops and detectors.
□
Use yellow-black strips or proper signals to identify dangerous
spots.
□
Before cleaning and maintenance operations,
disconnect the appliance from the mains by switching off the
master switch.
□
If removing the actuator, do not cut the
electric wires, but disconnect them from the terminal box by
loosening the screws inside the junction box.
INSTALLATION
All installation operations must be performed by a quali ed
technician, in observance of the Machinery Directive
2006/42/CE and safety regulations EN 12453 - EN 12445.
□
Verify the presence of a thermal-magnetic circuit breaker 0,03
A - 230 V - 50 Hz upstream the installation.
□
Use appropriate
objects to test the correct functionality of the safety
accessories, such as photocells, sensitive edges, etc.
□
Carry
out a risk analysis by means of appropriate instruments
measuring the crushing and impact force of the main opening
and closing edge in compliance with EN 12445.
□
Identify the appropriate solution necessary to eliminate and
reduce such risks.
□
In case where the gate to automate is
equipped with a pedestrian entrance, it is appropriate to
prepare the system in such a way to prohibit the operation of
the engine when the pedestrian entrance is used.
□
Apply
safety nameplates with CE marking on the gate warning about
the presence of an automated installation.
□
The installer must
inform and instruct the end user about the proper use of the
system by releasing him a technical dossier, including: layout
and components of the installation, risk analysis, veri cation of
safety accessories, veri cation of impact forces and reporting
of residual risks.
INFORMATION FOR END-USERS
The end-user is required to read carefully and to receive
information concerning only the operation of the installation
so that he becomes himself responsible for the correct use of it.
□
The end-user shall establish a written maintenance contract
with the installer/maintenance technician (on -call).
□
Any
maintenance operation must be done by quali ed technicians.
□
Keep these instructions carefully.
WARNINGS FOR THE CORRECT OPERATION OF THE
INSTALLATION
For optimum performance of system over time according to
safety regulations, it is necessary to perform proper
maintenance and monitoring of the entire installation: the
automation, the electronic equipment and the cables
connected to these.
□
The entire installation must be carried
out by quali ed technical personnel, lling in the Maintenance
Manual indicated in the Safety Regulation Book (to be
requested
or
downloaded
from
the
site
www.fadini.net/supporto/downloads).
□
Operator: maintenance inspection at least every 6 months,
while for the electronic equipment and safety systems an
inspection at least once every month is required.
□
The
manufacturer, Meccanica Fadini snc, is not responsible for
non-observance of good installation practice and incorrect
maintenance of the installation.
DISPOSAL OF MATERIALS
Dispose properly of the packaging materials such as
cardboard, nylon, polystyrene etc. through specializing
companies (after veri cation of the regulations in force at the
place of installation in the eld of waste disposal). Disposal of
electrical and electronic materials: to remove and dispose
through specializing companies, as per Directive 2012/19/UE.
Disposal of substances hazardous for the environment is
prohibited.
Meccanica Fadini s.n.c.
Director in charge
CE DECLARATION OF CONFORMITY of the manufacturer:
Meccanica Fadini snc (Via Mantova, 177/A - 37053 Cerea - VR - Italy) declares under own responsibility that:
Coral
complies
with the 2006/42/CE Machinery Directive, and also that it is sold to be installed in an “automatic system”, along with original
accessories and components as indicated by the manufacturing company. An automatic gate operator is, by law, a
“machinery” and therefore the installer must t the equipment with all of the applicable safety norms. The installer is also
required to issue the installer’s Declaration of Conformity. The manufacturer is not liable for possible incorrect use of the
product. The product complies with the following speci c norms: analysis of the risks and subsequent action to cure them
as per EN 12445 and EN 12453, Low Voltage Directive 2014/35/UE, Electromagnetic Compatibility 2014/30/UE. In order to
certify the product, the manufacturer declares under own responsibility the compliance with the EN 13241-1 PRODUCT
NORMS.
fully retractable oil-hydraulic bollard
