Factory CHRISTEN EAGLE II Assembly Manual Download Page 13 | Manualshive

Page: 13 / 23

background image

www.seagullmodels.com

13

Electric motor.

Battery.

Battery.

The propeller should not touch any part of the
spinner cone. If it does, use a sharp model-
ing knife and carefully trim away the spinner
cone where the propeller comes in contact with
it.

Install the spinner backplate, propeller
and spinner cone.

INSTALLING THE SPINNER.

M4 x 15mm.

M3x15mm.

Speed control.

4

«
...
11
12
13
14
15
...
»

Summary of Contents for CHRISTEN EAGLE II
























Reviews:

No comments

Related manuals for CHRISTEN EAGLE II

Brand: Lancair Pages: 8

ninjago Epic Dragon Battle 9450

Brand: LEGO Pages: 72

Brand: LEGO Pages: 36

Deere CONSTRUCTION LOADER

Brand: Peg-Perego Pages: 52

Touch & Learn Activity Desk Deluxe

Brand: VTech Pages: 10

SPINNER MISSILE

Brand: Rage Pages: 2

Smart Bluetooth Robot Car

Brand: Uctronics Pages: 42

Toot-Toot Drivers CustomisablePeople Carrier

Brand: VTech Pages: 11

Brand: Fisher-Price Pages: 24

Brand: Basic Fun Pages: 2

Thunderbolt Strike Roller Coaster

Brand: K'Nex Pages: 44

75005 Pocket Poker

Brand: Radica Games Pages: 2

BATHROOM EQUIPMENT SETS

Brand: Faller Pages: 4

Brand: Fisher-Price Pages: 5

Brand: Little Tikes Pages: 4

Hot Wheels Dune Racer W6201

Brand: Fisher-Price Pages: 28

Brand: E sky Pages: 29

Brand: JSF Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands