Factory CHRISTEN EAGLE II Assembly Manual Download Page 1 | Manualshive

Page: 1 / 23

background image

Kit features.

•

Ready-made—minimal assembly & finishing required.

•

Ready-covered covering.

•

Photo-illustrated step-by-step Assembly Manual.

Made in Vietnam.

Specifications

Wing span --------------------------------------- 53.9 in ----------------------------- 137cm.
Wing area --------------------------------------- 922.3 sq.in ------------------ 59.5 sq.dm.
Weight -------------------------------------------- 8.4-9.9 lbs --------------------3.8-4.5 kg.
Length -------------------------------------------- 47.4 in --------------------------- 120.5cm.
Recommended engine size ---------- 0.75-.91 cu.in ------------------------- 2-stroke.
--------------0.91-1.00 -1.25cu.in---------------- 4-stroke.

ELECTRIC CONVERSION : OPTIONAL.

Radio System required 6 channel with 6 digital servos.
Flying skill level ---------------------Intermediate/advanced.

ASSEMBLY MANUAL

MS:104

CHRISTEN

EAGLE II

1
2
3
...
»

Summary of Contents for CHRISTEN EAGLE II
























Reviews:

No comments

Related manuals for CHRISTEN EAGLE II

Traffic Light-Grand

Brand: Jamara Pages: 4

Mercedes-Benz Arocs

Brand: Jamara Pages: 4

Mercedes-AMG GT

Brand: Jamara Pages: 8

Liebherr 2,4 GHz

Brand: Jamara Pages: 8

Brand: Jamara Pages: 20

Beaver DHC 2 V2

Brand: Jamara Pages: 24

Brand: Jamara Pages: 16

Brand: Jamara Pages: 8

Brand: Faller Pages: 4

Brand: Tumama Kids Pages: 24

Brand: Carrera RC Pages: 40

Lynx Mk.8 interior

Brand: Eduard Pages: 4

Brand: Radio control model Pages: 8

Brand: Badger Basket Pages: 6

Brand: Eduard Pages: 6

Alphabert s Pen Pal Phonics

Brand: VTech Pages: 16

DESIGNER'S CHOICE 30 MODEL BUILDING SET

Brand: K'Nex Pages: 52

FIELD TRACK CROSSING

Brand: Faller Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands