background image

!! SAFETY PRECAUTIONS!!

WARNING:

 HAZARDOUS VOLTAGE.  SHOCK, BURNS

OR ELECTROCUTION CAN RESULT.  ALWAYS DISCON-
NECT THE BATTERIES BEFORE SERVICING MACHINE.

WARNING:

BATTERIES EMIT HYDROGEN GASES,

EXPLOSION OR FIRE CAN RESULT.  KEEP SPARKS AND
OPEN FLAMES AWAY.

WARNING:

CHARGE UNIT IN A WELL VENTILATED AREA,

AND KEEP BATTERY COMPARTMENT OPEN WHEN
CHARGING.  EXPLOSION OR FIRE COULD RESULT.

WARNING:

BATTERY ACID CAN CAUSE BURNS.

WEAR PROTECTIVE EYE WEAR AND GLOVES WHEN
SERVICING BATTERIES.

WARNING:

DO NOT STORE OUTDOORS OR PRESSURE

WASH.  PREVENT FROM GETTING ELECTRONIC
COMPONENTS WET.

WARNING:

THE USE OF PARTS AND SOLUTIONS OTHER

THAN RECOMMENDED BY THE MANUFACTURER MAY
CAUSE DAMAGE OR ENDANGER PEOPLE.

WARNING:

DRESS SAFELY. DO NOT WEAR RINGS

OR METAL WRIST WATCHES WHILE WORKING ON THIS
MACHINE.  THEY CAN CAUSE AN ELECTRICAL SHORT,
WHICH, CAN CAUSE SERIOUS BURNS.  DO NOT WORK
ON THIS MACHINE WHILE WEARING A TIE, SCARF OR
OTHER LOOSE, DANGLING NECKWARE OR CLOTHING.
THESE LOOSE ITEMS CAN TANGLE IN THE ROTATING
PARTS AND CAUSE SERIOUS INJURY OR EVEN DEATH.

WARNING:

DO NOT USE THE MACHINE AS A STEP

LADDER OR CHAIR.

WARNING:

 ONLY OPERATE THIS MACHINE FROM

THE OPERATORS SEAT.  IT WAS NOT DESIGNED TO
CARRY PASSENGERS.

WARNING:

DO NOT OPERATE THIS MACHINE ON RAMPS

OR UNEVEN SURFACES.  WHEN CLIMBING A RAMP,
ALWAYS DRIVE THE MACHINE IN FORWARD STRAIGHT
UP OR DOWN THE RAMP.  NEVER DRIVE ACROSS THE
INCLINE.  DO NOT BACK DOWN OR TURN ON RAMPS!

WARNING

: ALWAYS USE THE CHARGER PROVIDED

BY THE MANUFACTURER TO CHARGE THE MACHINE.
IT IS AN AUTOMATIC CHARGER, SPECIFICALLY
DESIGNED TO CHARGE AT THE APPROPRIATE RATE.
IF YOU MUST USE A DIFFERENT CHARGER,
DISCONNECT THE BATTERIES BEFORE CHARGING.
THIS WILL PREVENT DAMAGE TO THE ELECTRONIC
SPEED CONTROLLER.

WARNING:

UNDERSTAND THE DYNAMIC BRAKING

SYSTEM BEFORE YOU OPERATE THE MACHINE ON
RAMPS.  MACHINE DOES NOT COAST. RELEASING
THE FOOTPEDAL WILL AUTOMATICALLY APPLY
BRAKING FORCE, AND STOP THE MACHINE.

WARNING:

DO NOT PARK THE MACHINE ON

RAMPS OR SLOPES.  THE MACHINE HAS A PARKING
BRAKE, BUT IT IS RECOMMENDED THAT IT IS ALWAYS
PARKED ON LEVEL GROUND.

WARNING:

 DO NOT OPERATE THE MACHINE IF

ANY PARTS HAVE BEEN REMOVED OR DAMAGED.

WARNING:

DO NOT REMOVE, PAINT OVER, OR

DESTROY WARNING DECALS.  IF WARNING DECALS
BECOME DAMAGED, THEY MUST BE REPLACED.

WARNING:

DO NOT OPERATE MACHINE IN

UNSAFE CONDITION.  IF THE MACHINE IS IN NEED OF
REPAIR OR IS IN ANY WAY UNSAFE TO OPERATE,
THE MATTER SHOULD BE REPORTED IMMEDIATELY
TO THE SHIFT SUPERVISOR.  DO NOT OPERATE THE
MACHINE UNTIL IT IS RETURNED TO PROPER
OPERATING CONDITION.

WARNING:

 THIS MACHINE MUST ONLY BE

OPERATED BY TRAINED OPERATOR.  AS PART OF HIS
OR HER TRAINING, THEY MUST READ THIS MANUAL
THOROUGHLY.  IF EXTRA COPIES ARE NEEDED,
CONTACT YOUR LOCAL DEALER.

WARNING:

ALWAYS TURN OFF THE MACHINE,

BEFORE LEAVING IT UNATTENDED.

WARNING:

DO NOT OPERATE OVER ELECTRICAL

FLOOR OUTLETS.  MAY RESULT IN SERIOUS INJURY.

PAGE 6

Summary of Contents for 390 Series








































































Reviews: