background image

LIMITED LIFETIME WARRANTY ON BICYCLES AND FRAMESETS

Subject to the following limitations, terms and conditions, Factor warrants to the original owner 
for  the  lifetime  of  the  original  owner  of  each  new  Factor  bicycle  or  frameset  that  the  bicycle 
frame or frameset is free of defective materials and workmanship.

The  lifetime  limited  warranty  is  conditioned  upon  the  bicycle  being  operated  under  normal 
conditions  and  use,  and  properly  maintained  in  accordance  with  the  owner’s  handbook  (as 
supplied with the Factor bicycle).

This lifetime limited warranty does not apply to paint/finish, any Factor components considered 
subject  to  normal  wear  and  tear  or  any  third-party  components  attached  to  the  bicycle  or 
frameset, such as wheels, drive train, brakes, or any suspension related parts or components.

Any Factor components considered subject to normal wear and tear are covered under a limited 
one (1) year warranty. The duration of this limited warranty shall be one (1) year, commencing 
from the date the customer takes possession of the bicycle.

Factor  components  considered  subject  to  normal  wear  and  tear  will  be  listed  in  the  Technical 
Supplement and/or User Manual provided with the bicycle. Any and all third party components 
included  with  or  installed  on  Factor  bicycles  are  subject  to  any  manufacturers’  guarantee 
applicable to those components, as specified by the manufacturer.

Additional Conditions: This lifetime limited warranty is made solely to the original owner of this 
new Factor bicycle or frameset, and shall remain in force only as long as the original owner 

installation, it is recommended that the product be assembled by a qualified bicycle mechanic. 
FACTOR BIKES assumes no responsibility for damages or injury due to improper assembly and 
installation of the product(s).

To  qualify  for  FACTOR’S  LIMITED  LIFETIME  WARRANTY  please  visit  www.factorbikes.com  and 
register your product(s) within 15-days of purchase.

retains ownership of the Factor bicycle. This lifetime limited warranty is not transferable.

If  the  bicycle  is  purchased  as  a  gift,  the  original  recipient  of  the  gift  is  considered  to  be  the 
original owner for the purposes of this lifetime limited warranty.

In order to exercise your rights under this lifetime limited warranty, the bicycle or frameset must 
be presented to Factor or an authorized Factor dealer, together with a receipt, bill of sale, or 
other appropriate written proof of purchase which identifies the bicycle or frameset by serial 
number.

Exclusions & Limitations:

The above warranty, or any implied warranty, does not cover:

Modifications  from  the  original  condition  except  such  modifications  which  are  necessary  to 
comply with specific national legislative requirements that may apply in the country of use.

Normal wear and tear.

Use of the bicycle for abnormal and/or commercial activities, or for purposes other than those 
for which the bicycle was designed. Damage caused by failure to follow the instruction manual.

Paint finish and decal damage resulting from normal wear and tear, taking part in competition, 

INTRODUCTION

Congratulations  on  the  purchase  of  your  FACTOR  product.  Please  review  thoroughly  the 
following  instructions  and  only  follow  them  for  correct  operation  and  use.  Should  you  fail  to 
follow  the  following  instructions  and  warnings,  this  could  result  in  damage  of  the  product, 
damage to the bicycle and in severe situations cause possible injury and or death.

Since specific tools and bicycle service experience is required for proper assembly

Summary of Contents for Hanzo





















Reviews: