Installation and user manual
2 <
<
<
<
1
Dear user
Congratulations on purchasing your Faber product!
A quality product which will provide you with warmth
and atmosphere for many years when used correctly.
Please read the user manual before using the fire.
Should, despite the careful final checks, a malfunction
occur, please contact your dealer or Dimpco (Glen
Dimplex Ireland sales company) for assistance.
Please note:
The data of your fire is available in the user
manual.
Appliance data can be found on the type plate that can
be found behind the lower vermiculite back wall inside
the cassette.
Dimpco Ltd
Old Airport Road
Cloghran
Co Dublin
Ireland
Tel:
+353 (0) 1842 8222
Fax:
+353 (0) 1842 4943
Email:
Web:
www.dimpco.ie
1.1
Introduction
Only have the appliance installed by a qualified installer
according to local regulations.
Read this installation manual properly.
1.2
Please check
Check the fire for transport damage and report any
damage immediately to your dealer.
1.3
CE Declaration
Glen Dimplex Benelux certifies that this Faber fire
complies with the essential requirements for solid fuel
build in fires.
Model: Dimplex 510 I, 650 I, 700 I
Guidelines EG: 89/106/EEC
Harmonized Standards: NEN-EN-13240, NEN/EN-
13240/A2
This Declaration is invalid, if without the written
permission of Glen Dimplex Benelux:
Changes are made to the appliance.
The fire is connected to exhaust materials
other than specified.
2
Safety instructions.
Please read these instructions carefully before
installing or using this appliance. Failure to do
so may result in damage to persons and
property.
This appliance is suitable for domestic
heating use only in accordance with these
operating instructions. Do not make any
unauthorised changes to the appliance.
This appliance must be installed by a suitably
qualified competent person in accordance
with BS8308, Code of practice for installing
domestic heating and cooking apliances
burning solid mineral fuel. Installation must
comply with all Building Regulations,
including those referring to
Local Authority
Bye-Laws, National and European Standards
and Codes of Practice.
Chimney connections and fire safety must be
in compliance with local regulations and
standards following guidelines EN 13384, EN
1856-2 and EN 15287.
Do not install this appliance on a shared flue.
Do not fit an extractor fan in the same
room as this appliance.
Ensure there is adequate combustion air
ventilation in the room in accordance with
building standards. Do not obstruct any of the
air inlets or outlets on the appliance.
Due to the natural air convection of the
appliance, dust particles from carpets and
disrupted building materials or uncured paint
volatiles may settle on cold surfaces after
installation. Once installed allow some time
for dust to settle and vacuum clean before
lighting the appliance.
This appliance operates at very high
temperatures and retains its heat for a period
after use. Do not touch any surfaces while in
use. All persons including children and the
infirm should be warned of this and not
allowed to touch any surfaces while in use.
Please use a suitable fireguard manufactured
to BS 8423:2002 suitable for use with solid fuel
appliances, to prevent contact when in use.
Do not place any combustible items within
1m of the appliance (e.g. photographs,
paintings, TV’s, etc.). Exposure of combustible
items to hot surfaces or radiated heat will
cause damage and poses a serious fire risk.
Summary of Contents for Dimplex 510 I
