Faber CRISTAL 24, Installation Instructions Manual, Page: 7 / 14

Version 07/11 - Page 7
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/Off Switch
TheOn/Off switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light off.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower off.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut off when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
proper airflow. Allow the unit to operate for several minutes
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
The metal grease filters should be cleaned frequently in hot
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water, and use stainless steel cleaner
on the front strip. Using abrasives and scouring agents can
scratch rangehood finishes and should not be used to clean
finished surfaces.
FIGURE 10
FIGURE 7
FIGURE 8
Replacing the Halogen Lamps
Before attempting to replace the lamps, make sure that
the light switch is turned off. Remove the 2 screws (as
indicated in FIGURE 8) that hold the light support and
gently pull the support down from the hood. Remove
the lamp from the light support and replace with new
lamp. Replace the light support and fix it into place
with the 2 screws.
An alternative method to replace the lamps is to use a
1 1/4" suction cup ( FIGURE 9 ). Attach the suction cup
to the bulb and pull firmly down on the bulb and replace
with a new lamp. The hood uses a 20 Watt MR-11 type
halogen bulb with a lens cover.
FIGURE 9
EN
1
2
12
CARE
Grease filters
CLEANING METAL SELF- SUPPORTING GREASE FILTERS
• The filters must be cleaned every 2 months of operation, or
more frequently for particularly heavy usage, and can be
washed in a dishwasher.
• Remove the filters one at a time by pushing them towards the
back of the group and pulling up at the same time.
• Wash the filters, taking care not to bend them. Allow them to
dry before refitting.
• When refitting the filters, make sure that the handle is visible
on the outside.
Activated charcoal filter (Recirculating version)
These filters (not supplied with the rangehood)are not washable
and cannot be regenerated, and must be replaced approximately
every 4 months of operation, or more frequently with heavy us-
age.
REPLACING THE ACTIVATED CHARCOAL FILTER
• Remove the metal grease filters
• Remove the saturated activated charcoal filter as shown ( A ).
• Fit the new filters ( B ).z
• Replace the metal grease filters.
�
�
Lighting
LIGHT REPLACEMENT
20 W halogen light.
• Remove the 2 screws fixing the Lighting support, and pull it
out of from the Hood.
• Extract the lamp from the Support.
• Replace with another of the same type, making sure that the
two pins are properly inserted in the lamp holder socket holes.
• Replace the Support, fixing it in place with the two screws re-
moved as above.
EN
1
1
11
USE
Control board
L Light Switches the lighting system on and off.
M Motor Switches the extractor motor on and off.
V Speed Sets the operating speed of the extractor:
1. Low speed, used for a continuous and silent air change in the presence of
light cooking vapour.
2. Medium speed, suitable for most operating conditions given the optimum
treated air flow/noise level ratio.
3. Maximum speed, used for eliminating the highest cooking vapour emission,
including long periods.
�
�����
�
�
�
�
�
�
EN
1
2
12
CARE
Gre ase filt ers
CLE ANI NG M ETA L S ELF - S UPP ORT ING G REA SE FIL TER S
• T he filt ers m ust be clea ned ev ery 2 mon ths of op era tio n, o r
mor e f req uen tly fo r p arti cul arly h eav y u sag e, and c an be
was hed in a d ish was her .
• R em ove th e fi lter s o ne at a tim e b y p ush ing th em to war ds the
bac k o f th e g rou p an d p ulli ng u p at the sam e ti me.
• W ash th e fi lter s, t akin g c are no t to be nd the m. A llo w th em to
dry be for e re fitt ing .
• W hen re fitt ing th e fi lter s, m ake su re tha t th e h and le is visi ble
on the ou tsid e.
Act iva ted cha rco al f ilte r (R eci rcu lat ing ver sio n)
The se filt ers (no t s upp lie d w ith th e ra nge hoo d)a re not w ash abl e
and ca nno t b e re gen era ted , a nd mus t b e re pla ced ap pro xim atel y
eve ry 4 m ont hs of o per atio n, o r m ore fr equ ent ly with he avy us -
age .
REP LAC ING TH E A CTI VAT ED CHA RCO AL FIL TER
• Re mov e the m etal gre ase filte rs
• R em ove th e sa tur ated ac tiv ated ch arc oal filt er a s sh own ( A ).
• Fit the ne w filte rs ( B ).z
• R epl ace th e m etal gr eas e fi lter s.
�
�
Lig htin g
LIG HT REP LAC EM ENT
20 W h alo gen lig ht.
• R em ove th e 2 sc rew s fi xin g th e L igh tin g s upp ort, and pu ll i t
out of fro m th e H ood .
• E xtra ct t he l am p fr om th e S upp ort.
• R epl ace w ith an oth er of the sa me typ e, m aki ng sur e th at t he
two pin s ar e p rop erly ins erte d in the lam p h old er s ock et h ole s.
• R epl ace th e S upp ort, fix ing it in pla ce with th e tw o sc rew s re -
mov ed as a bov e.
GREASE FILTER REMOVAL
The grease filters are removed by pressing the handle on
the right side of the filter (FIGURE 7) . When replacing,
make sure that the filters are properly positioned with
the handles on the right and visible. There are 2 grease
filters, one in the slide out part of the hood, the other in
the back.
USE AND CARE INFORMATION
B