Fab Fours C3150 Installation Instructions Manual Download | Manualshive

Page: 15 / 21

background image

Installation Instructions

15 GMC HD Premium Front Bumper

Product Number: C3150, C3151, C3152

Application: 2015-2019 GMC HD

Copyright 2008 Fab Fours, Inc.

Page 15 of 21

C315X_REV_A

8.

Connect headlight and wires and fog light/turn signal
wires.

9.

Reattach headlight pods to truck

10.

Install turn indicators into the plastic light insert using
three self-tapping screws as shown below.

Figure 12a

11.

Install the light inserts with turn indicators into the cutout
in the bumper. Use the ¾” length ¼” stainless steel
button head, ¼” washers and hex nuts to fasten the insert
through the holes shown below.

«
...
13
14
15
16
17
...
»

Summary of Contents for C3150






















Reviews:

No comments

Related manuals for C3150

Brand: Makita Pages: 20

Brand: Panasonic Pages: 116

Toughbook CF-T7BWATAAM

Brand: Panasonic Pages: 12

Brand: AAT Pages: 6

Brand: Quincy lab Pages: 4

Leaf Wetness Sensor

Brand: Davis Instruments Pages: 2

M-Class Mark II M-4206

Brand: Datamax Pages: 22

Brand: DataCard Pages: 2

Brand: Yakima Pages: 11

Brand: ICON Pages: 8

Brand: oliser Pages: 6

Brand: rako Pages: 7

Brand: Saft Pages: 6

Brand: Xerox Pages: 16

Brand: Wagan Pages: 8

Brand: ADIC Pages: 6

Brand: Thermo King Pages: 2

Brand: Beurer Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands