background image

2

Avoid extreme

vibrations.

Do not cover 

the front screens.

Avoid moving objects 

and light sources in 

the detection field.

Avoid condensation.

Avoid the presence 

of smoke and fog in 

the detection field.

Avoid exposure to 

sudden and extreme 

temperature changes.

Keep the sensor 

permanently powered 

in environments where 

the temperature can 

descend below -10°C.

Wipe the front 

screens regularly 

with a clean and 

damp cloth.

Do not use aggressive 

products to clean 

the front screens.

Avoid direct exposure 

to high pressure 

cleaning.

SAFETY

INSTALLATION AND MAINTENANCE

Do not look into the laser 

emitter or the visible red 

laser beams.

The warranty is void if 

unauthorized repairs are 

made or attempted by 

unauthorized personnel. 

Only trained and qualified 

personnel may install and 

adjust the sensor. 

The manufacturer of the door system is responsible for carrying out a risk assessment and installing the sensor and the 

door system in compliance with applicable national and international regulations and standards on door safety and if 

applicable, the machinery directive 2006/42/EC. Other use of the device is outside the permitted purpose and can not be 

guaranteed by the manufacturer. The manufacturer cannot be held responsible for incorrect installations or inappropriate 

adjustments of the sensor.

Test the good functioning 

of the installation before 

leaving the premises.

The device contains IR and visible laser diodes.

IR laser: wavelength 905nm; max. output pulse power 75W 

(Class 1 according to IEC 60825-1)

Visible laser: wavelength 650nm; max. output CW power 3mW 

(Class 3R according to IEC 60825-1)

The visible laser beams are inactive during normal functioning.

The installer can activate the visible lasers if needed.

CAuTION!

 

Use of controls, adjustments or performance of procedures other than those specified herein 

may result in hazardous radiation exposure.

Summary of Contents for XGUARD-10













Reviews: