![background image](http://html1.mh-extra.com/html/faac/748/748_warnings-for-the-installer_3124067002.webp)
13
ENGLISH
ENGLISH
1) CAUTION! It is important for personal safety to follow all the instructions
carefully. Incorrect installation or misuse of the product may cause
people serious harm.
2) Read the instructions carefully before starting to install the product.
3) Packaging material (plastic, polystyrene, etc.) must not be left within reach
of children as it is a potential source of danger.
4) Keep the instructions in a safe place for future reference.
5) This product was designed and manufactured strictly for the use indicated
in this documentation. Any other not expressly indicated use may damage
the product and/or be a source of danger.
6) FAAC accepts no responsibility due to improper use of the automation or
use other than that intended.
7) Do not install the appliance in an area subject to explosion hazard: inflam-
mable gasses or fumes are a serious safety hazard.
8) The system must be constructed in compliance with the following Standards:
EN12604, EN12605, EN12453,EN12445 .
For non-EU countries, to obtain an adequate level of safety, the Standards
mentioned above must be observed, in addition to national legal
regulations.
9) FAAC will not accept responsibility if the principles of good workmanship
are disregarded in constructing the closing elements to be motorised, and
if any deformation occurs during use of the said elements.
10) Before carrying out any work on the system, switch off the electricity
supply.
11) The mains electricity supply of the automation must be fitted with a single-
pole switch with contact opening distance of 3mm or greater. Use of a 6A
thermal breaker with single-pole circuit break is recommended.
12) Make sure there is a differential switch with 0.03A threshold upstream of the
system.
13) Check that the earthing system is correctly made and connect the closure
metal parts to it. Also connect the Yellow/Green wire of the automation to
the earthing system.
14) The automation includes an intrinsic anti-crushing device consisting of a
torque control which, however, must be installed together with other safety
CE DECLARATION OF MACHINE CONFORMITY
(DIRECTIVE 89/392/EEC, ANNEX II, PART B)
Manufacturer :
FAAC S.p.A.
Address:
Via Benini, 1 - 40069 Zola Predosa BOLOGNA - ITALY
Declares that:
Operator mod. 748 with electronic control unit 748D,
• is manufactured to be incorporated in a machine or for assembly with other machines to constitute a machine
under the provisions of Directive 89/392/EEC, and subsequent amendments 91/368/EEC, 93/44/EEC, 93/68/EEC;
• conforms to the essential safety requirements of the following further EEC Directives:
73/23/EEC and subsequent amendment 93/68/EEC.
89/336/EEC and subsequent amendment 92/31/EEC and 93/68/EEC
and, furthermore, declares that putting the machine into service is forbidden until the machine in which it will
be incorporated or of which it will become a part has been identified and it has been declared as conforming
to the conditions of Directive 89/392/EEC and subsequent amendments enacted by the national implementing
legislation.
Bologna, 01 January 2002
The Managing Director
A. Bassi
devices.
15) The safety devices [e.g.: photocells, sensitive edges, etc…] protect any
dangerous areas against
Movement mechanical risks
, such as, crushing,
dragging, or shearing.
16) Use of at least one indicator-light is essential for each system (e.g.: FAAC
LAMP MINILAMP, etc.) as well as a sign adequately fixed to the frame
structure, in addition to the devices mentioned at point “16”.
17) FAAC accepts no responsibility regarding safety and correct operation
of the automation, should components made by manufacturers other
than FAAC be used in the system.
18) Use only FAAC original spare parts for maintenance.
19) Do not make any alterations to the components of the automation.
20) The installer must supply full information regarding manual operation of
the system in the event of an emergency and provide the user of the
system with the “User’s Guide” included with the product.
21) Do not allow children or other persons to stand near the product while in
operation.
22) Keep remote controls or any other pulse generator well away from chil-
dren, to prevent the automation from being activated accidentally.
23) The user must refrain from attempting to repair or adjust the system person-
ally and should contact qualified personnel only.
24) Anything not expressly provided for in these instructions is not permitted.
WARNING FOR THE INSTALLER
GENERAL SAFETY OBLIGATIONS