F5 BIG-IP 8950 Platform Manual Download Page 29 | Manualshive

Page: 29 / 56

background image

2. Loosen the power supply screw by turning it counterclockwise with an appropriate screwdriver, if

necessary.

Note: The screw that holds the ejector handle in place is captive and cannot be removed from the
assembly.

3. Grasp the ejector handle and rotate it downward to eject the power supply from the system.

4. Remove the power supply from the system by pulling straight toward you.

5. Ensure that the latch on the new power supply is in the down position and slide the power supply into

the power supply slot until the latch engages.

6. Rotate the latch upward to fully seat the power supply.

7. Tighten the screw into place.

The power supply is connected to the system when you tighten the screw completely.

8. Attach the power cord to the new power supply.

9. Ensure that the power switch, located on the power supply next to the screw, is in the ON position.

29

Platform Guide: 8950

«
...
27
28
29
30
31
...
»

Summary of Contents for BIG-IP 8950

























































Reviews:

No comments

Related manuals for BIG-IP 8950

Brand: NAIM Pages: 16

AirborneDirect ABDG-SE-IN5410

Brand: Quatech Pages: 8

EKI-152X series

Brand: Advantech Pages: 94

Brand: Sun Oracle Pages: 222

LaCinema PlayHD

Brand: LaCie Pages: 2

Brand: Supermicro Pages: 96

Brand: Supermicro Pages: 130

Brand: Supermicro Pages: 124

Brand: MRV Communications Pages: 65

Brand: Leightronix Pages: 22

Brand: ClearCube Pages: 2

NETWORK SATELLITE 5.2 - CHANNEL MANAGEMENT

Brand: Red Hat Pages: 268

Brand: ASUSTOR Pages: 11

Brand: Symetrix Pages: 4

Brand: Supermicro Pages: 70

Brand: Supermicro Pages: 78

Brand: Supermicro Pages: 82

Brand: Air Live Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands