F.u.n.k.e. TRT800A-OLED Operation And Installation Download Page 39

Page: 39 / 48

TRT800A / P/N 800ATC-A-(2xx)-(3xx)

Operation and Installation

Document-No: 03.2114.010.71e / Revision: 2.00

4.5.4

General Setup

Step

Display (Example)

1. Start-up Transponder

2. Ensure, the transponder-mode is

„STBY“. If necessary change the

mode by pressing

3. Press

A counter is shown at the upper-right

corner. Hold

till “ENTER SETUP”

is displayed.

4. After release of

the first setup

menu is displayed

……..select position (^)

rotary knob.....change value

Any menu item can be passed by

. If no changes are

made the original settings will remain stored. Modification of
one menu item does not impact the others. No entries will be
deleted.

AA :

EF123456

AC : 18
FID:

^BCDEFG

MOD=next

AA :

EF123456

AC : 18
FID:

ABCDEFG

MOD=next

ENTER SETUP 26

2000

FL 030

STBY 7000

Summary of Contents for TRT800A-OLED

















































Search results

Summary of Contents for TRT800A-OLED

Reviews:

Related manuals for TRT800A-OLED

Brands by name

Popular brands

F.u.n.k.e. TRT800A-OLED, Operation And Installation

Search results

Summary of Contents for TRT800A-OLED

Reviews:

Related manuals for TRT800A-OLED

Brands by name

Popular brands