EZPull RXP-02 Sporting clays Receiver Setup Manual
Using the Transmitter to setup timing functions:
The RXP02 can be set for several timing functions such as
delayed release, increased latch duration and reload delay.
1.
To enter the timing setup mode:
1.1.
With the receiver ON, hold the magnet directly on top of
the Pairing switch. Blue and Red LEDs will start
alternating. Keep holding the magnet until Blue and
Yellow LEDs start alternating. Remove the magnet.
1.2.
The receiver is now waiting for a “setup command” from
the transmitter. While waiting for a command, the LEDs
display the current timing settings in a repetitive loop.
1.3.
To abort timing setup mode, place the magnet above
the Pairing switch and remove it at once, the receiver will
return to normal operation.
2.
Setting the Release Delay: the RXP02 can be set for a
delayed release. This feature replaces expensive timers and
is useful in setting precision timing on following pairs.
2.1.
The yellow LED indicates the release delay:
2.1.1.
No Delay - Yellow blinks once
2.1.2.
Delay 1 Sec- Yellow blinks twice
2.1.3.
Delay 2 Sec- Yellow blinks three times
2.1.4.
Delay 3 Sec- Yellow blinks four times
2.2.
The [1-A] button on the transmitter adjusts the release
delay. Click the [1-A] button and observe the Yellow LED
blinking. The adjustment is cyclical. See above: 2.1.1. -
2.1.2. - 2.1.3. - 2.1.4. - 2.1.1. …
3.
Setting the Latch and Reload timing:
Latch time: some traps may require a longer period to
release a target. The RXP02 can be set to close the release
switch for a longer period of time.
Reload time: this feature is for use with EZPull controllers
that can throw a following pair from the same trap (Rafael).
3.1.
The Red LED indicates a longer reload period and the
Blue LED indicates longer latch time:
3.1.1.
Latch 0.4 Sec, Reload 2 Sec. – No lights
3.1.2.
Latch
0.6
Sec, Reload 2 Sec. – Blue LED
3.1.3.
Latch 0.4 Sec, Reload
4
Sec. – Red LED
3.1.4.
Latch
0.6
Sec, Reload
4
Sec. – Blue and Red LEDs.
3.2.
The [2-B] button on the transmitter adjusts the Latch
and Reload timing. Click the [2-B] button and observe
the LEDs. The adjustment is cyclical. See above: 3.1.1. -
3.1.2. - 3.1.3. - 3.1.4. - 3.1.1. …
4.
Save and Exit: Send a True pair A + B from the transmitter
to save and abort the setup mode.
4.1.
From TX-C2/3 or TX-VR2, press the [T] key.
4.2.
From TX-4 or MTX-8, press [TP], then select [1-A] and
[2-B] and then press [TP] again.
Troubleshooting:
Always use comparative approach to troubleshooting. If both
receivers don’t work, the problem is most likely with the
transmitter. If a transmitter works with one receiver but not with
the other, check the receiver, etc.
Receiver does not throw targets - Stand close to receiver. While
observing the LED indicators, press the respective key on the
transmitter:
1.
No lights – Check the receiver has power. Check that
transmitter indicators are on when you press the key.
2.
Red light on receiver turns on and Blue light turns off
momentarily– the target command was received – check
wiring to trap.
3.
Blue light turns off momentarily but no Red light – check
pairing with the transmitter. Follow the pairing procedure
described above.
