24
Owner’s Guide
INTRODUCTION
Read all of SAFETY and this section before attempting any procedure. Pay particular attention to Notices, Cautions, Warnings and Dangers.
USB Port (if equipped)
USB Port (3) is located to the right of the center compartment (Figure 4).
12-Volt Power Outlet (if equipped)
A 12-Volt power outlet (4) is located to the left of the center
compartment. The outlet supplies continuous power for any accessories
that have a 12-volt plug (Figure 4).
Parking Brake
This vehicle is equipped with an automatic parking brake; when the vehicle is stopped, the parking brake is automatically
set. The parking brake is released when the key switch and direction selector is in F (forward) or R (reverse) and the
accelerator is pressed. The parking brake is also released when the RUN/TOW switch is in the TOW or
(on European
Models) position with the key switch turned to N (neutral).
When the vehicle does not move forward or reverse, release the parking brake using the instructions located on the con-
troller splash shield below the seat on the passenger side of the vehicle.
To move the vehicle, turn the key switch to N, turn the RUN/TOW switch to the TOW position, move the vehicle to a safe
location on level ground, chock the tires, and turn the key to OFF.
In case of total power loss and the RUN/TOW switch does not release the parking brake, use the
instructions below the controller splash shield. Chock the tires to prevent the vehicle from moving when
the brake is released.
To read the instructions, remove three re-usable plastic rivets that secures the controller splash shield
to the body and the controller. To remove these rivets, press the center of the rivet with the vehicle key.
When the center pin goes into position the rivet can be removed. Repeat the procedure for each
remaining rivet. Turn the splash shield over to read the instructions.
This procedure must be performed by qualified trained personnel.
Make sure that the key switch is in the OFF position and
chock the tires to prevent the vehicle from moving; Then do
the following:
•
Locate the ‘Auxiliary Power’ line (7) and remove the
weather pack seal (8) from the connector (Figure 5).
•
Locate the ‘Primary Power’ line connector (5) and dis-
connect it from line (6).
•
Connect the ‘Auxiliary Power’ line (7) to the ‘Primary
Power’ line (5) which releases the brake. If the tires are
not chocked and the vehicle is not on flat ground the
vehicle will move immediately.
•
Move the vehicle to desired, safe location and chock
the tires immediately.
•
Disconnect the ‘Auxiliary Power’ line (7) from the ‘Pri-
mary Power’ line (5).
•
Connect the ‘Primary Power’ line (5) to line (6).
•
Replace the weather pack seal (8) on the ‘Auxiliary
Power’ line connector (7).
4
3
Figure 4 Center Compartment
609694
Failure to follow these instructions can result in DEA
TH or SERIOUS INJUR
Y
THIS PROCEDURE SHOULD ONL
Y BE T
O CLEAR VEHICLE FROM
AN UNSAFE
AREA
AND BE PERFORMED
ONL
Y BY
QUALIFIED TRAINED PERSONNEL
In Case Of T
otal Power Loss
And The ‘Run-tow’
Switch DOES NOT Release The Brake T
o Move The V
ehicle:
Turn the ignition key to the ‘OFF’
position and ‘chock’
tires to prevent inadvertent movement.
Connect ‘Auxiliary Power
’ line (3) to ‘Primary Power
’ line (1) which will release the brake.
THIS WILL
CAUSE
THE VEHICLE
TO MOVE IMMEDIA
TEL
Y IF NOT
ON LEVEL
GROUND.
Move vehicle to desired location and park it properly on level ground, chock tires, IMMEDIA
TEL
Y
DISCONNECT
‘AUXILIAR
Y POWER’
AND RECONNECT
‘PRIMAR
Y POWER’
(1, 2) FOR SAFETY
AND
TO A
VOID BA
TTER
Y DRAIN.
Reconnect the W
eather Pack Seal (4) to the
Auxiliary Power line (3) and perform required service
procedures following all Safety guidelines as outlined in your repair manual.
Identify the ‘Auxiliary Power
’ line (3) and remove the W
eather Pack Seal (4) from the connector
.
Identify the ‘Primary Power
’ line (1) connector and disconnect the line (2).
7
8
5
6
Figure 5 Splash Shield and Parking Brake Release
