background image

 

 

Control Panel Operation

 

BUTTON 

FUNCTION 

ACTION & INDICATION 

  

 

POWER 

ON

: Enables control panel functions and 

remote control. Turns on flame effect. 

OFF

: Disables control panel functions and    

remote control. Turns off flame effect. 

 

 

1. 

Press once

, indicator light turns on.  

Power turns on. All functions enabled. 

2. 

Press again

, flame effect turns off. 

Power and all functions turn off.  

 

FLAME button

: Adjusts flame brightness. 

NOTE:

 Flame effect stays on until power 

button is turned off. Flame effect must be 
on for heater to turn on. 

1.

 Press once

, indicator light turns on. 

    

Flame brightness changes. 

2. 

Press again,

 until desired brightness is 

    selected.  

 

COLOUR button

: Adjusts the flame 

colour. 

NOTE:

 Colour effect stays on until power 

button is turned off. Colour flame effect 
must be on for heater to turn on.

 

  

1. 

Press once

, indicator light turns on. 

    

Flame colour changes. 

2. 

Press again

, until desired colour is 

    

selected. 

 

 

HEATER

 

HEATER button

: Turns heater on and off.   

NOTE:

 The heater only works when the 

flame effect is on. If the flame effect is off, 
the heater will not turn on. 

NOTE:

 To prevent overheating, the heater 

blows cool air for 10 seconds before the 
heater turns on, and after it turns off. 

NOTE: 

Heater overrides room temp 

control. 

1. 

Press once

, indicator light turns on.

 

Fan blows cool air for 10 seconds. Low 
heater (H1) turns on and blows warm air. 

2. 

Press again

, indicator light remains on. 

High heater (H2) turns on and blows hot 
air. 

3. 

Press again,

 indicator light turns off. Fan 

    blows cool air for 10 seconds, then turns 

    off. 

 

 

 

TEMP   

 

TEMPERATURE button: 

Turns heater on 

and off to maintain room at a certain 
temperature. 

NOTE:

 Press & hold the button for 5 

seconds, the temperature setting will 
switch from 

 to 

 and vice versa. 

P   1. 

Press once, 

indicator light turns on.       

         Temperature is preset at 18

 

.

 

3.  2.

 Press again, 

until desired room  

4.

 

     

temperature is selected.

 

 

 

 

Summary of Contents for Celestial 600


















Reviews: