TLP Pro 525T, 725T, and 1025T Series • Setup Guide (Continued)
100-240V
~
50-60Hz
0.4A MAX
XTP
PWR
XTP PWR
To network switch
To touchpanel
1
1
2
2
3
3
Figure 4.
Connecting to a Power Injector
Connecting the Power injector
The power injector must be purchased separately. Figure 4 shows the Extron
XTP PI 100. Your power injector may look different.
Connect a straight-through Ethernet cable from the power injector to a
switch or router (see figure 4,
1
). This cable carries network information
from the switch or router to the power supply input. A second straight-
through cable (
2
) carries the network information and 48 VDC from the
power injector to the touchpanel LAN/PoE connector (see
figure 3
,
F
, on
the previous page). Connect the IEC power cord to a convenient 100 VAC to
240 VAC, 50-60 Hz power source (
3
).
Reset Modes: a Brief Summary
The TLP Pro 525T, 725T, and 1025T Series touchpanels offer the following reset modes:
•
Use Factory Firmware:
Use this mode with Toolbelt software to replace firmware in the event of conflicts arising from
uploading a firmware update.
Press and hold the
Reset
button (see
C
) while applying power to the unit.
•
Reset All IP Settings:
Use this mode to reset all network settings without affecting user-loaded files.
Press and hold the
Reset
button until the
Reset
LED (
E
) blinks twice (about 6 seconds).
Release and momentarily press the
Reset
button again.
•
Reset to Factory Defaults:
Use this mode to return the touchpanel to factory default settings.
Press and hold the
Reset
button until the
Reset
LED blinks three times (about 9 seconds).
Release and momentarily press the
Reset
button again.
•
Enable or Disable the
DHCP Client:
Use this mode to toggle between DHCP enabled and DHCP disabled.
Press the
Reset
button five times, consecutively. After the fifth press, do not press the button
again within 3 seconds. If DHCP was enabled, it is now disabled and the
Reset
LED blinks three
times. If DHCP was disabled, it is now enabled and the
Reset
LED blinks six times.
Setup Menu
Figure 5 shows the
Setup
menu
Status
screen for the
TLP Pro 725T model. The menu screens for all other models are very
similar.
Press the
Menu
button (see
figure 3
,
B
) to open the
Setup
menu. Select any of the five available screens (
Status
,
Network
,
Display
,
Audio
, and
Advanced
) by pressing the appropriate
button in the navigation bar at the top of the screen (for more
information, see the
TLP Pro 525, 725, and 1025 Series User Guide
).
Info
Model:
TLP Pro 725T
Part Number: 60-1562-02
Firmware
Version:
1.02.0000.b003
PoE:
Active
Network
IP Address:
DHCP:
Host Name:
Off
192.168.254.251
TLI-AB-CD-EF
Display
Resolution:
Project:
Sleep Timer:
1024x600
1024x600
5 Minutes
Audio
Master Volume:
Master Mute:
Off
100
Status
Display
Audio
Advanced
Exit
Network
Advanced
Controller IP:
192.168.254.250
Project Size:
1/197 MB
Bootloader
Version:
1.03.0000
Figure 5.
Setup Menu: Status Screen for TLP Pro 725T
4
68-2831-54 Rev. A
01 19
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide
on the Extron website.
For information about replacing and disposing of batteries, see the
TLP Pro 525, 725, and 1025 Series User Guide
at
www.extron.com
.
© 2019 Extron Electronics — All rights reserved.
www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters:
Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
