4
SME 100 • Setup Guide (Continued)
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West
Extron USA - East
+1.714.491.1500 +1.919.863.1794
+1.714.491.1517 FAX
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
(Inside Asia Only)
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+4000.398766
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
Inside India Only
+91-80-3055.3777
+91 80 3055 3737 FAX
©
2012 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners.
www.extron.com
68-2167-50
Rev.
A
01 12
3.
Press the Next button repeatedly to cycle to the IP address (IP), subnet mask (SM), and
default gateway (GM) submenus.
4.
Change the IP address, subnet mask, and default gateway as necessary.
To configure the addresses:
z
Cycle to the desired octet by rotating the left Adjust knob (
[
).
z
Adjust the value of the octet by rotating the right Adjust knob (
{
).
5.
Save the network settings by pressing the Menu button. The network settings of the
SME 100 are now configured.
NOTE:
If the Edit Comm Settings menu is left inactive for approximately 30 seconds, a
menu timeout occurs and any changes made within this menu are not saved. The
Menu button must be pressed to save changes.
About the Web-based User Interface
The web-based user interface is used to view, configure, and control the SME 100. This section
details how to access the web-based user interface and install media player software. For more
information on using the web-based user interface, see the
SME 100 User Guide
.
Accessing the Web-based User Interface
Open a web browser (Microsoft
®
Internet Explorer
®
version 7 or
above is recommended) on the control PC or viewing device and type
in the IP address of the SME 100 into the address bar (for example,
http://192.168.254.254). The Live View page appears in the browser
(see figure 1). Proceed to the section below to install the media player
software that is compatible with the SME 100.
Installing Media Player Software
The SME 100 uses a media player plugin to view live streams. The plugin
available in
VLC media player
®
is compatible with the SME 100. Use the
following procedure to install VLC media player. For information on
installing the
QuickTime
®
media player, see the
SME 100 User Guide
.
1.
If necessary, access the web-based user interface of the SME 100
(see the "
Accessing the Web-based User Interface
" section above).
2.
From the Live View page, click the first
here
link (see figure 1). If the link shown in figure 1 does not appear on the
Live View page and a blue player window (with Extron logo) is displayed, it means that a version of VLC media player is
already installed. Verify that the installed VLC media player is version 1.1.10. If version 1.1.10 is not installed, uninstall
VLC media player and repeat this procedure.
NOTE:
A yellow security bar may appear at the top of the browser window after the first
here
link is clicked. If this
happens, click the security bar and click
Download File
, then click the first
here
link again.
3.
A File Download window appears. Click the
Run
button to download and start the VLC media player installation.
Follow the directions on the remaining prompts to install the player.
NOTE:
During installation of VLC media player, a Choose Components window will appear that contains a
Select the type of install
drop-down menu. Make sure that the
Full
installation is selected.
4.
After the VLC media player installation has finished, a reboot of the control PC or viewing device is recommended.
5.
Access the web-based user interface (see the "
Accessing the Web-based User
Interface
" section above). The Live View page should now contain a blue
player window (with Extron logo). Click the
Play
icon to view a live stream.
NOTES:
•
When a live stream is played, by default it uses the unicast RTP transport protocol. To change the transport
protocol and other various settings on the SME 100, click on the
Configuration
tab, then click on the
Encoder Settings
link on the left sidebar.
•
Clicking on the
©
icon located in the upper right hand corner of the web page lists the licensed third-party
software that is used by the SME 100 (see figure 2).
AUDIO
CONFIG
EXIT MENU
PRESS NEXT
Next
ADVANCED
CONFIG
Next
Next
EDIT COMM
SETTINGS
SERIAL PORT
9600 RS232
DHCP MODE
<OFF> ON
I 192.168
P 254.254
AUDIO
CONFIG
OUTPUT
CONFIG
Next
S 255.255
M 000.000
G 000.000
M 000.000
Next
Next
Figure 1.
Live View Page
Figure 2.
Licensed Third-party Software
