Extron electronics SME 100 Setup Manual Download Page 1

1

SME 100 • Setup Guide

 
 
The Extron SME 100 is a live streaming media encoder that interfaces with DVI, RGB, HDTV,  
and standard definition signals for delivering media over IP networks. It features a  
three input video and audio switcher, plus buffered loop-throughs for simplified integration into AV systems. The SME 100 
uses H.264 / MPEG-4 AVC encoding to output an IP stream over the Internet (or over an intranet) that can easily be decoded 
and viewed on PCs or H.264 compatible devices.
Two versions are available: The 

SME 100 HD

 (part number 

60-1061-01

) or the 

SME 100 SD

 (part number 

60-1061-02

).  

The only difference between the two versions is that the SME 100 SD only supports standard definition output rates.
This guide provides basic instructions for an experienced installer to set up and operate the SME 100. Installation and service 
must be performed by authorized personnel only.

NOTE:

  See the 

SME 100 User Guide 

for complete installation, configuration, operation, and mounting information.  

The user guide is available at 

www.extron.com

.

Rear Panel Overview

RS-232

RESET

Tx  Rx

100-240VAC      

50/60 Hz

0.5A MAX

R-Y

Y/

VID

B-Y/

C

RGB/R-Y,Y,B-Y/YC/VID

DVI-D

BUFFERED LOOP

BUFFERED LOOP

1

1

2

INPUTS

AUDIO

3

L

R

2

L

R

3

L

R

LAN

ACT LINK

1

4

5

3

2

6

7

10

8

9

12

11

a

  AC power connector 

 

 

 

 

 

g

  DVI buffered loop connector

b

  Component, S-video, composite BNC connectors (input 1) 

 

h

  Audio captive screw connectors (inputs 1 – 3)

c

  Component, S-video, composite BNC buffered loop connectors 

i

  Buffered loop audio captive screw connectors

d

  15-pin HD connector (input 2) with EDID emulation  

 

j

  RS-232 connector

e

  15-pin HD buffered loop connector 

 

 

 

k

  Reset button and LED

f

  DVI connector (input 3) with EDID emulation 

 

 

l

  RJ-45 Ethernet connector

Installation

Step 1 — Mount the SME 100

Turn all devices off and unplug their power cords. Verify that the SME 100 is disconnected 
from the power source. Mount the SME 100 to a rack using the mounting brackets 
included with the unit (see image at right).

Step 2 — Connect Input Devices

Connect input devices to at least one of the following connectors.

 

z

Connect a video input device to the component, S-video, or composite BNC connectors  
(input 1; 

b

). See the image below to connect the necessary signal format.

1

B-Y/

C

S-video (YC)

Y

/

VID

R-Y

1

R-Y

Y

/

VID

B-Y

/

C

Component Video (Y, R-Y, B-Y)

Composite Video

1

Y/
VID

B-Y/
C

R-Y

 

z

Connect a video input device to the 15-pin HD connector (input 2; 

d

). See pin configurations below.

Signal

Pin 1

Pin 2

Pin 3

Pin 13 Pin 14

RGBHV

R

G

B

H

V

RGBS

R

G

B

S

RGBcvS

R

G

B

S

RGsB

R

Gs

B

Rack Mount
Bracket

Signal

Pin 1

Pin 2

Pin 3

Pin 13 Pin 14

YUV

R-Y

Y

B-Y

S-video

Y

C

Video

Vid

1

2

13

3

14

Reviews: