background image

This guide provides basic instructions for an experienced installer to set up and operate the  

Extron

®

 MMX 32 VGA MTP mini matrix switcher.

N

  For full installation and operating details, refer to the 

MMX 32 VGA MTP Users’s Guide

,

available online at 

www.extron.com

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the MMX 32 VGA MTP as 

required (rack, furniture, or tabletop mounted).

Step 2 — Connect inputs

Connect up to three video sources (RGBHV, RGBS, RGsB, RsGsBs, 

component video, S-video or composite video) to the female 15-HD 

connectors, inputs 1-3.  

Connect audio sources to the 3.5 mm stereo jacks and wire the audio 

connectors as shown at right.

Step 3 — Connect outputs

Attach the applicable output cables (video, audio, and video and audio) as below:

a.  Video output 1 —

 Connect a display device to this female 15-pin HD connector.

b.  Audio output 1 —

 Connect speakers to this 3.5 mm stereo jack.

c.   Audio/Video (RGB) output 2 —

 Connect an MTP U R series or other MTP receiver 

to this RJ-45 UTP connector. 

Wire the connector as shown at right. 

Connect a projector or other RGB video 

output device to the receiver, and 

connect speakers for summed (L and R) 

mono audio output.

d.  Audio output 2 —

 Connect speakers 

to this 5-pole, 3.5 mm captive screw 

connector for balanced/unbalanced 

audio and wire connector for dual mono 

output as shown below.  

L

MONO A

UDIO

R

L

MONO A

UDIO

R

Unbalanced Output

Balanced Output

Do not tin the wires!

Mono output 1-

Sleeve(s)

Mono output 1+

Mono output 2+

Mono output 2-

Sleeve(s)

Mono output 1

Mono output 2

NO GROUND.

NO GROUND.

C

 

For unbalanced audio, connect both sleeves to the center (ground)

  contact.  DO NOT connect the sleeves to the negative (-) contacts.

Setup Guide  — MMX 32 VGA MTP 

NOTE

   If you are using Enhanced Skew-Free™ A/V

 

 

cable, use the TIA/EIA T568A standard only.

Insert Twisted
Pair Wires

Pins:

12345678

RJ-45 Connector

5

Pin

1

Red+/V. sync+

2

Red–/V. sync–

3

Mono audio+

Green–

6

Mono audio–

7

Blue+/H. sync+

8

Blue–/H. sync–

4

Wire color

White-green

Green
White-orange

White-blue

Orange
White-brown
Brown

Wire color

568 A

568 B

Signal

White-orange

Orange
White-green

White-blue

Green
White-brown
Brown

Green+

Blue

Blue

INPUT 2 

INPUT 1 

AUDIO 

AUDIO 

OUTPUT 1 

AUDIO 

INPUT 3 

AUDIO 

REMOTE 

AUDIO 

MMX 32 VGA MTP 

OUTPUT 1 

OUTPUT 2 

RS-232 

+5V 

POWER 

12V 

0.5A MAX 

 

1    2    3 

 

 

CONT

A

CT 

Tx  Rx 

SYNC - 

TRI 

PRE PEAK - ON

 

OUTPUT 2 

RGB/AUDIO 

Sleeve (   )

Ring (R)

Tip (L)

3.5 mm TRS Stereo 

Plug Connector

(unbalanced)

1

Summary of Contents for MMX 32 VGA MTP

Page 1: ...ce to the receiver and connect speakers for summed L and R mono audio output d Audio output 2 Connect speakers to this 5 pole 3 5 mm captive screw connector for balanced unbalanced audio and wire connector for dual mono output as shown below L MONO AUDIO R L MONO AUDIO R Unbalanced Output Balanced Output Do not tin the wires Mono output 1 Sleeve s Mono output 1 Mono output 2 Mono output 2 Sleeve s...

Page 2: ...g To compensate for signal loss over long cable runs set the DIP switch position up on down off as shown in the table below Video Format Cable length Signal quality at max distance Pre Peak Off Pre Peak On High Variable Composite S video Component 800 ft 245 m 1000 ft 300 m 640 x 480 300 ft 90 m 350 ft 105 m 700 ft 215 m 750 ft 230 m 800 x 600 300 ft 90 m 350 ft 105 m 550 ft 165 m 650 ft 200 m 102...

Page 3: ...gh the Extron Simple Instruction Set SIS or the Extron Universal Switcher Control Program When audio breakaway is active the front panel input LED for the audio source flashes while the LED of the video source lights steadily Device Control Output control Momentarily short the rear panel Remote contact pin 1 2 or 3 for the desired output to ground to switch to that input Use the 5 V port when cont...

Page 4: ...te X 1B VmtX 1 Mute RGB output X RGB unmute X 0B VmtX 0 Unmute RGB output X Read RGB mute X B X Show RGB mute status X Global where X is not included global RGB mute is activated RGB mute all 1 B Vmt1 Mute all RGB RGB unmute all 0 B Vmt0 Unmute all RGB Audio mute Audio mute X 1Z AmtX 1 Mute audio output X Audio unmute X 0Z AmtX 0 Unmute audio output X Read audio mute X Z X Show audio mute status X...

Reviews: