Extron electronics IP Link IPL EXP 200 User Manual Download Page 3

Copyright and Trademark Notices

Copyright

© 2021  Extron. All rights reserved. 

www.extron.com

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks (®), registered service marks (

SM

), and trademarks (™) are the property of RGB Systems, Inc. or Extron (see the current list 

of trademarks on the 

Terms of Use

 page at 

www.extron.com

):

Registered Trademarks

 

(®)

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, eLink, Flat Field, FlexOS, Glitch Free, Global Configurator, 
Global Scripter, GlobalViewer, Hideaway, HyperLane, IP Intercom, IP Link, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort, NAV,  
NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation, 
System 

I

ntegrator

, TeamWork, TouchLink, V‑Lock, VN‑Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTP Systems, and ZipClip

Registered Service Mark

(SM)

 :  

S3 Service Support Solutions

Trademarks

 

(™)

AAP, AFL (Accu‑RATE Frame Lock), ADSP (Advanced Digital Sync Processing),  AVEdge, CableCover, CDRS (Class D Ripple Suppression), Codec 
Connect, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator, DSVP (Digital Sync  
Validation Processing), EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, Opti‑Torque, PendantConnect, 
ProDSP, QS‑FPC (QuickSwitch Front Panel Controller), Room Agent, Scope‑Trigger, SIS, Simple Instruction Set, Skew‑Free, SpeedNav, Triple‑Action 
Switching, True4K, True8K, Vector

 4K, WebShare, XTRA, and ZipCaddy

   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for IP Link IPL EXP 200





















































Reviews: