manualshive.com logo in svg

Extron electronics IP Link IPL EXP 200, User Manual, Page: 24 / 52

Share
Download
Extron electronics IP Link IPL EXP 200 User Manual Download Page 24

IPL EXP I/O Series • Hardware Features and Installation

16

1   2   12V24V G

3   4   12V24V G

+V OUT / DIGITAL I/O

5   6   12V24V G

7   8   12V24V G

12 VDC / 24 VDC

19W MAX TOTAL

12 VDC and 24 VDC Power Output

Use these ports to power accessories such as occupancy sensors. 

Total maximum output is 19 watts, if a PoE+ power supply is used to 

power the IPL EXP RIO8. These ports are always on, unless the total 

load reaches the overload condition.
Global Configurator software provides a way to monitor these ports.
• 

Normal operation mode

—The load drawn by connected devices 

is 0 - 17 watts.

• 

Limit mode

—The total load on these ports is between 17 and 19 

watts.

• 

Overload mode

— The load has reached or exceeded 19 watts. 

All power output ports shut off. Power will be restored after you 

correct the excessive power draw from the connected devices.

Sensor, LED,

accessory, 

or similar item

Sensor, LED,

accessory, 

or similar item

12V

G

24V

G

Heat

Shrink

Over

Shield

Wires

Rear Panel, IPL EXP RIO8

Ground

Share the same ground among 
I/O connections.

Device 2 digital I/O

with 24 VDC
Device 1 digital I/O

Wire
Nut

IPL EXP RIO8

1 

2 

12V24V 

G3

 

4 

12V24V 

G

RELA

YS

3

4

7

8

1

2

5

6

+V OUT / DIGI

TA

L I/O

5 

6 

12V24V 

G7

 

8 

12V24V 

G

12 VDC /

24 VD

C

19W MAX TOT

AL

LAN / PoE

+

GGG

Ground

Digital 

Input

Ground

Power

24 VDC

Power

12 VDC

Occupancy

Control Output

Ceiling

Ceiling Tile

Hanger Clip

Extron

OCS 100C

Occupancy 

Sensor

Extron 

IPL EXP RIO8

Expansion Interface

LAN/PoE

LAN

Extron 

ECM S10 Rx

Receiver does not detect
signal from transmitter.

ECM S10 Tx

Partition closed 

Figure 6. 

 Wiring the DC Power Output Ports

Can add this once the device is shipping:

IPL EXP RIO8

1 

2 

12V24V 

G3

 

4 

12V24V 

G

RELA

YS

3

4

7

8

1

2

5

6

+V OUT / DIGI

TA

L I/O

5 

6 

12V24V 

G7

 

8 

12V24V 

G

12 VDC /

24 VD

C

19W MAX TOT

AL

LAN / PoE

+

Ground

Digital Input 1

Digital Input 2

Ground

Power

24 VDC

Power 12 VDC

Occupancy

Control Output

Ceiling

Ceiling Tile

Hanger Clip

Extron 

Occupancy 

Sensor

Extron 

IPL EXP RIO8

Expansion Interface

LAN/PoE

LAN

Extron

Room

Availability

Indicator

Summary of Contents for IP Link IPL EXP 200





















































Reviews:

No comments