manualshive.com logo in svg

Extron electronics FPC 6000, User Manual

Share
Download
Extron electronics FPC 6000 User Manual Download Page 14

Mounting

When the FPC 6000 ships, it is housed in a 7U high, 19 inch wide, rack-mountable panel that 
can be installed in any standard equipment rack or control console. Follow the instructions below 
and read the 

Underwriters Laboratories (UL) Guidelines for Rack Mounting

 on the next 

page.

ee

FPC 6000

#10-32 screws (4)

Figure 2. 

Rack Mounting the FPC 6000

Installing the FPC 6000 in a Rack or Control Console

The FPC 6000 is housed in a rack-mountable panel when it ships.

ATTENTION:

• 

All structural steps and electrical installation must be performed by qualified personnel 
in accordance with local and national building codes and electrical codes.

• 

Toute étape structurelle et installation électrique, doit être effectuée par un personnel 
qualifié, conformément aux codes du bâtiment, aux codes incendie et sécurité, et 
aux codes électriques, locaux et nationaux.

• 

Do not install the FPC 6000 in a fire resistant rated wall or partition assembly.

• 

Ne pas installer le FPC 6000 dans un mur résistant au feu ou une cloison.

figure 2

FPC 6000 • Mounting

6

Summary of Contents for FPC 6000
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands