2
DTP2 R 212 Series • Setup Guide (Continued)
(see
on page 1) — Connect an STP cable between a compatible Extron DTP transmitting device
SIG
LINK
DTP2 IN
on page 8 to properly wire the connector and for detailed
NOTES
).
use the receiver to remotely power a legacy DTP unit. Circuit damage to the transmitter WILL result.
•
NE PAS
utiliser le récepteur pour alimenter à distance un émetteur de la gamme existante DTP. Cette opération
FINIRA par endommager le circuit menant à l’émetteur.
Signal LED indicator
— Lights green when the receiver accepts a video signal.
Link LED indicator
— Lights yellow when a device is connected and communication is established.
RS-232
IR
Tx
Tx
G
Rx
Rx
OVER DTP2
2
(input 2) — Plug a serial RS-232 signal, a modulated IR signal (up to 40 kHz), or both
into this 3.5 mm, 5-pole captive screw connector for bidirectional RS-232 and IR communication (see
on page 6 to wire the connector). RS-232 and IR data can be transmitted simultaneously.
— Connect an HDMI cable between this port and an HDMI video display. See
on
page 7 to use the LockIt HDMI Cable Lacing Bracket to secure the connector to the switcher.
NOTE:
The maximum HDMI cable length is 4.5 m (15 feet).
— Connect an audio device such as an audio amplifier or powered speakers to this 5-pole, 3.5 mm
L
R
captive screw connector. This connector outputs unamplified, line level audio, whether it is from an analog input to the
transmitter or de-embedded from the transmitter HDMI input (see
on page 10 to wire the
connectors).
This connector can be tied to the amplified output (SA models) so that the volume varies as the amplified output varies or fixed at
0 dB.
L
R
4/8 OHM
CLASS
WIRING
(DTP2 R 212 SA only) — Connect unpowered, 4-ohm or 8-ohm speakers to this 4-pole 5 mm
captive screw connector to play the amplified stereo audio output.
— If desired, connect serial bidirectional RS-232 signals to this 3.5 mm, 5-pole captive screw
RS-232
Tx Rx G
DISPLAY
connector for control of a connected display device via the DTP transmitter. (see
(DTP2 R 212 SA only) — The volume of the amplified audio output can be controlled via a hard-wired
C G
V
10V 50mA
potentiometer control, such as the Extron VC 50, the VCM 100 Series devices, and the VCM 200 Series devices. A locally-
constructed device can also be used (see the
DTP2 R 212 User Guide
for assembly guidelines).
NOTE:
The Volume switch (
I
) must be in the
Volume
Port
(down) position for a device connected to this port to
control the volume.
(DTP2 R 212 SA only) — Set this switch as follows to select how the amplified output volume is controlled.
VOL
— The volume of the amplified audio output can be controlled via the RS-232 port by issuing SIS
commands or the Product Configuration Software.
— The volume of the amplified audio output can be controlled via a local control device
connected to the Volume port (H).
— Plug a serial RS-232 device into the switcher via this 3.5 mm, 3-pole captive screw connector for
RS-232
Tx
G
Rx
remote control of the switcher (see
on page 6 to wire the connector).
— If desired, for remote control of the networked switcher, connect the switcher to a PC or to an Ethernet LAN via
LAN
Act (yellow) LED
— The Act LED indicates transmission of data packets on the RJ-45 connector. This LED blinks as the
switcher communicates.
Link (green) LED
— The Link LED indicates that the switcher is properly connected to an Ethernet LAN. This LED lights steadily.
— Plug the included external 12 VDC power supply into this 2-pole connector.
POWER
12V
2.0 A MAX
